How to service and repair the antenna cable on right-hand drive on Mercury Cougar?

Begin right-hand drive antenna cable service and repair by taking out both the overhead console and message center. Begin by removing the antenna cable retaining screw then removing the antenna base along with its gasket from the roof surface. Use a tool to remove the right-hand side sun visor together with its clip by releasing the locking mechanism. The technician should remove the right-hand A-pillar trim panel and the scuff panel trim before gently lowering the right-hand side of the headliner. First remove the right-hand cowl side trim panel by disconnecting the antenna cable both from retaining clips and A-pillar clip. Begin by unconnecting the liftgate release switch electrical connector then take out the cowl side trim panel before completing the process with disconnecting the antenna cable electrical connector and freeing its wiring harness from its retaining clip. Start by removing the instrument panel lower panel before detaching the wiring harness clip from the relay mounting bracket and separating the relays together with their electrical connectors from this mounting bracket. The right-hand side vent pipe along with the relay mounting bracket should be removed by extracting its two bolts before setting the bracket aside. Ending the procedure requires disconnecting the antenna wire from its retaining bracket then positioning the sound damping panel before removing the antenna cable. The installation process follows the reverse steps of removal.

How to service and repair the antenna cable for satellite radio without navigation on Mercury Mariner?

Service of satellite radio antenna cable requires first removing the Right Hand A-pillar trim panel and Right Hand sun visor. You should lower the headliner front enough to access the satellite radio antenna electrical connector and then disconnect this connector before removing the antenna. Proceed to break the satellite radio antenna cable connection from its place at the Satellite Digital Audio Receiver System (SDARS) module electrical connector. You should undo both the installation methods when installing the setup. New satellite radio antenna placement should follow the harness route for vehicles that have navigation systems. All these installations require proper securing.

OEM Mercury Antenna Cable

Radio Antenna Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

39 Antenna Cables found

View related parts
Mercury Antenna Cable, Front Part Number: AE5Z-18812-E
$25.04 MSRP: $34.64
You Save: $9.60 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Extension; Antenna Cable, Front
- Manufacturer Note: Attaches To Radio Receiver
- Position: Front
- Replaces: AE5Z-18812-A
Fits the following Mercury Models:
- Milan | 2010-2011 | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Antenna Cable Part Number: 8E5Z-18812-B
$33.85 MSRP: $46.06
You Save: $12.21 (27%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Extension
Fits the following Mercury Models:
- Milan | 2007-2009 | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Extension, Front Part Number: 6W7Z-18812-A
Product Specifications
- Other Name: Cable Assembly - Extension; Antenna Cable, Front; Cable
- Position: Front
Fits the following Mercury Models:
- Grand Marquis | 2006-2011 | GS, LS | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Cable Part Number: F6DZ-18812-AC
Product Specifications
- Other Name: Cable Assembly - Extension; Antenna Cable
- Manufacturer Note: Radio antenna cable
Fits the following Mercury Models:
- Sable | 2000-2005 | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Antenna Cable Part Number: F5TZ-18812-A
Product Specifications
- Other Name: Cable Assembly - Extension
Fits the following Mercury Models:
- Mountaineer | 1997-2002 | Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Antenna Cable, Front Center Part Number: 8G1Z-18812-B
Product Specifications
- Other Name: Cable Assembly - Extension; Antenna Cable, Front Center
- Position: Front Center
Fits the following Mercury Models:
- Sable | 2008-2009 | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Antenna Cable Part Number: 98BZ-18812-MA
Product Specifications
- Other Name: Cable Assembly - Extension; Cable
- Manufacturer Note: In,line connector to antenna
Fits the following Mercury Models:
- Cougar | 1999-2002 | Base, S, V6 | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Mercury Cable Part Number: F6AZ18812BA
Product Specifications
- Other Name: Cable Assembly - Extension
Fits the following Mercury Models:
- Grand Marquis | 1996 | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Antenna Cable Part Number: 1L2Z-18812-HA
Product Specifications
- Other Name: Cable Assembly - Extension; Cable
- Manufacturer Note: Connects To Antenna
Fits the following Mercury Models:
- Mountaineer | 2001 | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Antenna Cable Part Number: 3F2Z-18812-AA
Product Specifications
- Other Name: Cable Assembly - Extension
Fits the following Mercury Models:
- Monterey | 2004-2007 | Base, Convenience, Luxury, Premier | 6 Cyl 4.2 L GAS
View related parts
Mercury Antenna Cable Part Number: 3F2Z-18812-BA
Product Specifications
- Other Name: Cable Assembly - Extension
Fits the following Mercury Models:
- Monterey | 2004-2007 | Base, Convenience, Luxury, Premier | 6 Cyl 4.2 L GAS
View related parts
Mercury Antenna Cable Part Number: 5L2Z-18812-AB
Product Specifications
- Other Name: Cable Assembly - Extension; Cable Assembly
Fits the following Mercury Models:
- Mountaineer | 2002-2007 | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Antenna Cable Part Number: 5L2Z-18812-BA
Product Specifications
- Other Name: Cable Assembly - Extension; Cable
Fits the following Mercury Models:
- Mountaineer | 2002-2005 | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Extension Part Number: 5W7Z-18812-BA
Product Specifications
- Other Name: Cable Assembly - Extension
- Manufacturer Note: Radio antenna lead-in cable assembly, #2 in illustration, short wheel base only, attaches to antenna connector, 3825mm (12.50 feet)
Fits the following Mercury Models:
- Grand Marquis | 2003-2005 | GS, GSL, Limited Edition, LS, LSE, Ultimate Edition | 8 Cyl 4.6 L GAS
- Marauder | 2003-2004 | Base | 8 Cyl 4.6 L GAS
View related parts
Mercury Antenna Cable, Rear Passenger Side Part Number: 6E5Z-18812-AA
Product Specifications
- Other Name: Cable Assembly - Extension; Antenna Cable, Right
- Position: Rear Passenger Side
Fits the following Mercury Models:
- Milan | 2006 | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Antenna Cable Part Number: 6E5Z-18812-BA
Product Specifications
- Other Name: Cable Assembly - Extension
Fits the following Mercury Models:
- Milan | 2006 | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Antenna Cable Part Number: 6E5Z-18812-CA
Product Specifications
- Other Name: Cable Assembly - Extension
Fits the following Mercury Models:
- Milan | 2006 | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Cable, Center Part Number: 6W7Z-18812-E
Product Specifications
- Other Name: Cable Assembly - Extension; Antenna Cable, Center
- Position: Center
- Replaces: 6W7Z-18812-C
Fits the following Mercury Models:
- Grand Marquis | 2006-2011 | GS, LS | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Cable, Rear Part Number: 7W7Z-18812-A
Product Specifications
- Other Name: Cable Assembly - Extension; Antenna Cable, Rear; Amplifier
- Position: Rear
- Replaces: 6W7Z-18812-B
Fits the following Mercury Models:
- Grand Marquis | 2003-2011 | GS, GSL, Limited Edition, LS, LSE, Ultimate Edition | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
- Marauder | 2003-2004 | Base | 8 Cyl 4.6 L GAS
View related parts
Mercury Antenna Cable Part Number: 8E5Z-18812-A
Product Specifications
- Other Name: Cable Assembly - Extension
- Replaces: 7E5Z-18812-B
Fits the following Mercury Models:
- Milan | 2007-2009 | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS

| Page 1 of 2 |Next >

1-20 of 39 Results

Mercury Antenna Cable

If you own Mercury and want to keep it in top shape, choosing OEM Antenna Cable is a smart move. They are precisely engineered and follow strict factory standards. They are made in advanced facilities that use cutting edge technology. Each part goes through thorough testing to confirm strength and safety, so you can trust it. FordPartsDeal.com gives you genuine Mercury Antenna Cable at some of the affordable online prices without cutting quality. Every OEM Mercury part includes the manufacturer's warranty, easy returns, and super-fast delivery. So why wait? Shop now and get your vehicle back to peak condition.

Mercury Antenna Cable provides excellent radio reception through connecting any radio antenna directly to the car tuner. Mercury started in 1938 and applied the name of the winged god and pursued a compromise between rideability and affordability. Mercury showrooms were selling spacious cabins, hushed interiors and crisp lines that enabled drivers to feel high end without spending much. Mercury cars such as Cougar and Grand Marquis were able to prove the fact with millions of people who decided their self-assured position and tender suspension. Mercury continued to adjust comfort tech over the decades until the 2011 halt of production but the badge continues to convey value minded style. Potholes were absorbed by using soft springs and reinforced bushings that maintained steering fast to respond to lane change. Consumers adored plush benches, balanced dashboards and radios that did not bang their wallets. Antenna Cable is installed in the rear of dash panels and keeps vulnerable signals hidden behind the noise of engines and the unforgiving road vibration. Antenna Cable consists of tight copper windings and a durable jacket such that even many years of door banging do not reduce the signal strength. Antenna Cable can be connected to any product between towering screw-in whips and stealth glass strips to current shark fin allowing users to change the hardware at any time. The failure of an Antenna Cable appears as a non-functional or dead air and thus it only takes a few minutes of replacement of lead to ensure that playlists and traffic alerts are back. Its miniature connectors can be installed in factory openings without soldering without any drama. The flexible core of the cable is also resistant to cold snaps, heat waves and tight bends and has the cable remaining rattle free and the wires undamaged.

Mercury Antenna Cable Parts and Q&A

Antenna Cable
98BZ-18812-MA
Q: How to service and repair the antenna cable on right-hand drive on Mercury Cougar?
A:
Begin right-hand drive antenna cable service and repair by taking out both the overhead console and message center. Begin by removing the antenna cable retaining screw then removing the antenna base along with its gasket from the roof surface. Use a tool to remove the right-hand side sun visor together with its clip by releasing the locking mechanism. The technician should remove the right-hand A-pillar trim panel and the scuff panel trim before gently lowering the right-hand side of the headliner. First remove the right-hand cowl side trim panel by disconnecting the antenna cable both from retaining clips and A-pillar clip. Begin by unconnecting the liftgate release switch electrical connector then take out the cowl side trim panel before completing the process with disconnecting the antenna cable electrical connector and freeing its wiring harness from its retaining clip. Start by removing the instrument panel lower panel before detaching the wiring harness clip from the relay mounting bracket and separating the relays together with their electrical connectors from this mounting bracket. The right-hand side vent pipe along with the relay mounting bracket should be removed by extracting its two bolts before setting the bracket aside. Ending the procedure requires disconnecting the antenna wire from its retaining bracket then positioning the sound damping panel before removing the antenna cable. The installation process follows the reverse steps of removal.
Antenna Cable
8L8Z-18812-C
Q: How to service and repair the antenna cable for satellite radio without navigation on Mercury Mariner?
A:
Service of satellite radio antenna cable requires first removing the Right Hand A-pillar trim panel and Right Hand sun visor. You should lower the headliner front enough to access the satellite radio antenna electrical connector and then disconnect this connector before removing the antenna. Proceed to break the satellite radio antenna cable connection from its place at the Satellite Digital Audio Receiver System (SDARS) module electrical connector. You should undo both the installation methods when installing the setup. New satellite radio antenna placement should follow the harness route for vehicles that have navigation systems. All these installations require proper securing.