How to Address Issues with the Brake Backing Plate on a Mercury Villager?

The first step for fixing the backing plate starts by uninstalling the wheel cylinder followed by the wheel hub dust cap. The process starts with removing the cotter pin before you take away the hub nut along with the washer. Complete the first step by removing the hub and bearing assembly and second step involves removing the parking brake lever. The backing plate demands a passage for the parking brake cable which should be followed by securing the rear anti-lock brake (ABS) sensor out of the way by its bolt. You must first move the ABS sensor aside before extracting the rear brake backing plate through the removal of its securing bolts. Recovery of the installation requires following the reverse order of the removal steps to finish the job.

How to Properly Maintain the Brake Backing Plate on a Mercury Mariner?

Start the brake backing plate service by deleting the rear wheel cylinder from the system. Replacement requires the removal of brake flexible hose bracket bolt which needs tightening to 15 Nm (133 lb-in) during reinstallation. Use a tool to compressor the parking brake cable conduit locking tabs and draw the parking brake cable assembly through the backing plate. The service requires users to first take off the rear wheel hub along with four backing plate bolts that detach the backing plate until reinstallation tighten the bolts to 85 Nm (63 lb-ft). The setup process will finish with the reverse order of the previous removal procedures.

How to service and repair the brake backing plate on Mercury Sable?

The brake backing plate requires maintenance that must begin by taking out the brake drum. First remove the wheel cylinder before disconnection of the parking brake cable. You should unclip the parking brake cable and conduit from the brake backing plate while guiding them outside the backing plate. The service requires removal of the ABS sensor bolt which will be discarded after service. You must remove both backing plate securing bolts before discarding them along with the bolts. Proceed with installation by following the opposite steps of removal and use new bolts.

OEM Mercury Brake Backing Plate

Brake Dust Shield

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

59 Brake Backing Plates found

View related parts
Mercury Backing Plate, Rear
Part Number: F4ZZ-2C028-A
$11.10 MSRP: $17.18
You Save: $6.08 (36%)
Product Specifications
- Other Name: Shield - Brake Disc Splash; Brake Dust Shield, Rear; Splash Shield; Brake Dust Shield
- Position: Rear
- Replaces: E8OY-2C028-A
Fits the following Mercury Models:
- Sable | 1989-1992 | GS, LS | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Mercury Splash Shield, Driver Side
Part Number: F5AZ-2K005-A
Product Specifications
- Other Name: Shield - Splash; Brake Dust Shield
- Position: Driver Side
Fits the following Mercury Models:
- Grand Marquis | 1995-2002 | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Splash Shield, Front Passenger Side
Part Number: 3W1Z-2K004-AA
Product Specifications
- Other Name: Shield - Splash; Brake Dust Shield, Front Right; Brake Dust Shield
- Position: Front Passenger Side
Fits the following Mercury Models:
- Grand Marquis | 2003-2011 | GS, GSL, Limited Edition, LS, LSE, Ultimate Edition | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
- Marauder | 2003-2004 | Base | 8 Cyl 4.6 L GAS
View related parts
Mercury Splash Shield, Front Passenger Side
Part Number: 6L2Z-2K004-A
Product Specifications
- Other Name: Shield - Splash; Brake Dust Shield, Front Right; Dust Shield; Brake Dust Shield
- Position: Front Passenger Side
Fits the following Mercury Models:
- Mountaineer | 2006-2010 | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Splash Shield, Front Driver Side
Part Number: 6L2Z-2K005-A
Product Specifications
- Other Name: Shield - Splash; Brake Dust Shield, Front Left; Dust Shield; Brake Dust Shield
- Position: Front Driver Side
Fits the following Mercury Models:
- Mountaineer | 2006-2010 | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Backing Plate, Driver Side
Part Number: E5AZ2212A
Product Specifications
- Other Name: Plate Assembly - Brake Back; Brake Dust Shield
- Position: Driver Side
Fits the following Mercury Models:
- Colony Park | 1987-1991 | GS, LS | 8 Cyl 5.0 L GAS
- Grand Marquis | 1984-1991 | Base, Colony Park, GS, LS | 8 Cyl 5.0 L GAS, 8 Cyl 5.8 L GAS
- Marquis | 1985-1986 | Base, Brougham | 4 Cyl 2.3 L GAS, 6 Cyl 3.8 L GAS
View More
View related parts
Mercury Splash Shield, Passenger Side
Part Number: F5AZ-2K004-A
Product Specifications
- Other Name: Shield - Splash; Brake Dust Shield
- Position: Passenger Side
Fits the following Mercury Models:
- Grand Marquis | 1995-2002 | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Backing Plate, Rear
Part Number: F5OY-2C028-A
Product Specifications
- Other Name: Shield - Brake Disc Splash; Brake Dust Shield, Rear; Splash Shield; Brake Dust Shield
- Position: Rear
Fits the following Mercury Models:
- Sable | 1996-2005 | G, GS, LS, LS Premium | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Backing Plate, Rear Passenger Side
Part Number: F65Z-2211-AA
Product Specifications
- Other Name: Plate Assembly - Brake Back; Brake Backing Plate, Rear Left, Rear Right; Brake Dust Shield
- Manufacturer Note: Plate asy. - rear wheel brake - RH
- Position: Rear Passenger Side
Fits the following Mercury Models:
- Mountaineer | 2001 | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Backing Plate, Rear Driver Side
Part Number: F65Z-2212-AA
Product Specifications
- Other Name: Plate Assembly - Brake Back; Brake Backing Plate, Rear Left, Rear Right; Brake Dust Shield
- Manufacturer Note: Plate asy. - rear wheel brake - LH
- Position: Rear Driver Side
Fits the following Mercury Models:
- Mountaineer | 2001 | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Splash Shield, Front Driver Side
Part Number: 6E5Z-2K005-AA
Product Specifications
- Other Name: Shield - Splash; Brake Dust Shield, Front Left; Brake Dust Shield
- Position: Front Driver Side
Fits the following Mercury Models:
- Milan | 2006-2011 | Base, Hybrid, Premier | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Splash Shield, Front
Part Number: YL8Z-2K004-AA
Product Specifications
- Other Name: Shield - Splash; Brake Dust Shield, Front; Dust Shield; Brake Dust Shield
- Manufacturer Note: RH/LH
- Position: Front
Fits the following Mercury Models:
- Mariner | 2005-2011 | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Backing Plate, Rear Passenger Side
Part Number: CL8Z-2B540-A
Product Specifications
- Other Name: Bracket; Disc Brake Caliper Bracket, Rear Right; Brake Dust Shield; Caliper Mount
- Position: Rear Passenger Side
- Replaces: 6L8Z-2C220-A, 6L8Z-2B540-C, 6L8Z-2B540-A
Fits the following Mercury Models:
- Mariner | 2005-2007 | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Backing Plate, Rear Driver Side
Part Number: CL8Z-2B540-B
Product Specifications
- Other Name: Bracket; Disc Brake Caliper Bracket, Rear Left; Brake Dust Shield; Caliper Mount
- Position: Rear Driver Side
- Replaces: 6L8Z-2B540-B, 6L8Z-2B540-D, 6L8Z-2C220-B
Fits the following Mercury Models:
- Mariner | 2005-2007 | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Splash Shield, Front Passenger Side
Part Number: 1L2Z-2K004-AB
Product Specifications
- Other Name: Shield - Splash; Brake Dust Shield, Front Right; Brake Dust Shield
- Position: Front Passenger Side
Fits the following Mercury Models:
- Mountaineer | 2002-2005 | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Splash Shield, Front Driver Side
Part Number: 1L2Z-2K005-AB
Product Specifications
- Other Name: Shield - Splash; Brake Dust Shield, Front Left; Brake Dust Shield
- Position: Front Driver Side
Fits the following Mercury Models:
- Mountaineer | 2002-2005 | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Backing Plate, Rear Passenger Side
Part Number: 3F2Z-2C028-AA
Product Specifications
- Other Name: Shield - Brake Disc; Brake Backing Plate, Rear Right; Brake Dust Shield; Splash Shield; Shield - Brake Disc Splash
- Position: Rear Passenger Side
Fits the following Mercury Models:
- Monterey | 2004-2007 | Base, Convenience, Luxury, Premier | 6 Cyl 4.2 L GAS
View related parts
Mercury Backing Plate, Rear Driver Side
Part Number: 3F2Z-2C029-AA
Product Specifications
- Other Name: Shield - Brake Disc; Brake Backing Plate, Rear Left; Brake Dust Shield; Splash Shield; Shield - Brake Disc Splash
- Position: Rear Driver Side
Fits the following Mercury Models:
- Monterey | 2004-2007 | Base, Convenience, Luxury, Premier | 6 Cyl 4.2 L GAS
View related parts
Mercury Splash Shield, Front Passenger Side
Part Number: 3F2Z-2K004-AA
Product Specifications
- Other Name: Shield - Splash; Brake Dust Shield, Front Right; Brake Dust Shield
- Position: Front Passenger Side
Fits the following Mercury Models:
- Monterey | 2004-2007 | Base, Convenience, Luxury, Premier | 6 Cyl 4.2 L GAS
View related parts
Mercury Splash Shield, Front Driver Side
Part Number: 3F2Z-2K005-AA
Product Specifications
- Other Name: Shield - Splash; Brake Dust Shield, Front Left; Brake Dust Shield
- Position: Front Driver Side
Fits the following Mercury Models:
- Monterey | 2004-2007 | Base, Convenience, Luxury, Premier | 6 Cyl 4.2 L GAS

| Page 1 of 3 |Next >

1-20 of 59 Results

Mercury Brake Backing Plate Parts Questions & Experts Answers

Backing Plate, Passenger Side
F3XY2211A
Q: How to Address Issues with the Brake Backing Plate on a Mercury Villager?
A: The first step for fixing the backing plate starts by uninstalling the wheel cylinder followed by the wheel hub dust cap. The process starts with removing the cotter pin before you take away the hub nut along with the washer. Complete the first step by removing the hub and bearing assembly and second step involves removing the parking brake lever. The backing plate demands a passage for the parking brake cable which should be followed by securing the rear anti-lock brake (ABS) sensor out of the way by its bolt. You must first move the ABS sensor aside before extracting the rear brake backing plate through the removal of its securing bolts. Recovery of the installation requires following the reverse order of the removal steps to finish the job.
Splash Shield, Front
YL8Z-2K004-AA
Q: How to Properly Maintain the Brake Backing Plate on a Mercury Mariner?
A: Start the brake backing plate service by deleting the rear wheel cylinder from the system. Replacement requires the removal of brake flexible hose bracket bolt which needs tightening to 15 Nm (133 lb-in) during reinstallation. Use a tool to compressor the parking brake cable conduit locking tabs and draw the parking brake cable assembly through the backing plate. The service requires users to first take off the rear wheel hub along with four backing plate bolts that detach the backing plate until reinstallation tighten the bolts to 85 Nm (63 lb-ft). The setup process will finish with the reverse order of the previous removal procedures.
Backing Plate, Front Passenger Side
4F1Z-2K004-AA
Q: How to service and repair the brake backing plate on Mercury Sable?
A: The brake backing plate requires maintenance that must begin by taking out the brake drum. First remove the wheel cylinder before disconnection of the parking brake cable. You should unclip the parking brake cable and conduit from the brake backing plate while guiding them outside the backing plate. The service requires removal of the ABS sensor bolt which will be discarded after service. You must remove both backing plate securing bolts before discarding them along with the bolts. Proceed with installation by following the opposite steps of removal and use new bolts.