Ford E5RY-13466-B
Backup Lamp Bulb, Amber/Clear, Rear Outer

Service of the headlamp bulb necessitates turning both the headlamp switch and ignition switch OFF. Begin by removing the battery. Start by releasing the rear cover retainer and thereafter removing the rear cover. The electrical connector needs removal followed by extracting the low beam or high beam bulb. Follow the reminder instructions to install the new bulb after completion of removal steps. The halogen headlamp bulb requires gentle handling by holding the base only to prevent damaging the sealed glass envelope since it carries pressurized gas that fractures upon contact or dropping. The bulb needs removal only right before bulb installation since extended removal exposes it to performance-damaging contaminants that could enter the headlamp. You must never enable the headlamps when the bulb remains disconnected.

The first step for servicing instrument cluster bulbs requires uninstallation of the instrument cluster (IC). The illumination bulb can be extracted by rotating it counterclockwise a quarter turn and then removing it from the IC. The procedure for installation should follow the steps of reverse bulb removal.

Begin service of instrument cluster bulb by unfastening the instrument cluster. The bulb must be rotated by one quarter turn toward the opposite direction before being raised out of the instrument cluster. The installation process for the new bulb begins by following the exact steps of removal in reverse order.

A proper service of fog lamp bulbs starts by putting both the headlamp switch and ignition switch into their OFF position. Put the vehicle in NEUTRAL mode then secure it on a hoist. After disconnecting the electrical connector you should remove the fog lamp bulb while only holding the base and avoid any contact with the glass envelope. This is essential to prevent personal injury from unstable gas inside the bulb which could break upon touching it. Keeping the bulb inside the fog lamp for a long time reduces performance quality and exposes the lamp to possible contamination which could settle on the lens and reflector. It is dangerous to activate the fog lamps when operating without a bulb in place. You should put in the new bulb by repeating the steps for removing it.

Services of the left-hand headlamp bulb require both the headlamp switch and ignition switch to be in the OFF position. The initial step should involve removing the air cleaner intake pipe. The service requires removing the headlamp bulb protective cover while disconnecting its electrical connector to take out the bulb. Handle the bulb base only because touching the glass envelope will result in gas difficulties and potential breakage from scratches or drops. installation of the new bulb requires you to follow the reverse order of removal using caution to close the protective cover completely. The bulb needs immediate installation and should never come into contact with external contaminants since these substances will impact its performance. Also keep the headlamps devoid of power when the bulb remains uninstalled.

The service of the left-hand side headlamp bulb requires first verifying both headlamp and ignition switches are turned off. Equipment with 2.3L and 3.0L engine configuration needs the air cleaner intake pipe as your first step for removal. The service begins with removing the protective cover from the headlamp bulb then disconnecting its electrical connector to free the bulb. Take the opposite order for new bulb installation by placing the protective cover correctly sealed while following the same removal sequence in reverse. People should handle the bulb by its base exclusively because pressure-loaded gas in the bulb can harm users if the glass envelope breaks after experiencing scratches or drops. The bulb removal should wait until right before installation to stop pollutants from entering the headlamp components that could impact system performance. Leaving the headlamps in operation with a removed bulb is unsafe at all times.

Service of the courtesy lamp bulb begins by removing the interior assembly. The first task is to release the tang before opening the reflector so you can reach the interior lamp bulb to remove it. The process for inserting the new bulb follows the opposite sequence of bulb removal steps.

The instrument cluster needs removal as the first step to service or repair instrument panel bulbs. Begin by extracting the suitable bulb. You can install the instrument panel bulb by reversing the steps of removal.

Reverse the removal procedure, ensuring that the headlamp bulb protective cover is completely sealed.

It may affect headlamp bulb performance and allow contaminants to enter the headlamp.

Position the vehicle in NEUTRAL on a hoist.

Disconnect the headlamp electrical connector, ensuring that the headlamp switch and ignition switch are in the OFF position.

The headlamp bulb should not be removed until just before a new bulb is installed.

The fog lamp bulb contains gas under pressure.

Rotate it one quarter turn counterclockwise and lift it out from the instrument cluster.

Bulbs 9004 and 9007 appear similar but are not interchangeable.

First, remove the HID bulb access cover, then take out the two screws and the HID bulb, disconnecting the electrical connector.

Disconnect the fog lamp electrical connector, then squeeze both tabs on the fog lamp bulb simultaneously to remove it.

Reverse the removal procedure.

Remove the instrument cluster.

Avoid removing the bulb for an extended period, as this may affect the performance of the headlamp bulb and allow contaminants to enter the headlamp.

Disconnect the electrical connector, remove the fog lamp bulb, and then install the new bulb by reversing the removal procedure.

Handle the halogen bulb carefully, as it contains gas under pressure and may shatter if the glass is scratched or if the bulb is dropped. Grasp the bulb only by its base and avoid touching the glass envelope to prevent personal injury.

By grasping only its base and avoiding contact with the glass envelope.

Take out the instrument cluster bulbs.

Extended exposure may affect performance due to contaminants entering the fog lamp.

Extended exposure can affect performance due to contaminants entering the headlamp and settling on the lens and reflector.

Carefully disconnect the electrical connector.

Reverse the removal procedure.

Ensure the headlamp switch and ignition switch are both in the OFF position.

First, remove the headlamp assembly.

The headlamp bulb should not be removed from the assembly until just before installing a new bulb.

Reverse the removal procedure.

Rotate the bulb approximately one-eighth turn counterclockwise to remove it, then disconnect the electrical connector.

Release the four tabs on the selector lever bezel and lift the bezel up to the selector lever knob.

Rotate it one quarter turn counterclockwise and lift it out from the instrument cluster.

Begin by removing the headlamp assembly.

Remove the headlamp assembly and then the headlamp cover.

Ensure the headlamp switch and ignition switch are turned OFF.

Handle the bulb only by its base to avoid shattering due to pressure or contamination.

Handle it carefully as it contains gas under pressure and may shatter if the glass is scratched or if the bulb is dropped; always grip the bulb by its base and avoid touching the glass envelope to prevent personal injury.

Begin by removing the headlamp assembly.

Disconnect the headlamp connector and take out the headlamp bulb.

Reverse the removal procedure.

The fog lamp bulb should not be removed until just before installation to prevent contaminants from affecting performance.

The headlamp switch and ignition switch should both be in the OFF position.

Installation is achieved by reversing the removal steps.

Take out 8 screws and 5 pin-type retainers.

Ensure the headlamp switch and ignition switch are in the OFF position.

Reverse the removal procedure.

First, remove the instrument cluster.

To avoid personal injury, as the bulb contains gas under pressure and may shatter if the glass envelope is scratched or dropped.

Simply reverse the removal procedure.

Reverse the removal procedure.

The headlamp switch and ignition switch should be in the OFF position.

Ensure the headlamp switch and ignition switch are both in the OFF position.

Install the new bulb(s) by reversing the removal procedure.

The bulb contains gas under pressure and may shatter if mishandled.

Release the spring retainer to remove the HID bulb and disconnect the electrical connector.

Handle the bulbs carefully, as they contain gas under pressure and may shatter if the glass envelope is scratched or if the bulb is dropped. Avoid touching the glass envelope and do not leave the bulb exposed for an extended period.

Position the vehicle in NEUTRAL on a hoist, release the tabs to remove the fog lamp bulb, and disconnect the electrical connector.

Exercise caution as the halogen bulb contains gas under pressure and may shatter if the glass envelope is scratched or if the bulb is dropped; handle the bulb only by its base and avoid touching the glass envelope to prevent personal injury.

The vehicle should be in NEUTRAL and positioned on a hoist.

Grasp only the base of the bulb and avoid touching the glass envelope, as the bulb contains gas under pressure and may shatter if mishandled.

Reverse the removal procedure while continuing to handle the bulb with care to prevent injury.

First, raise and support the vehicle.

Begin by removing the headlamp assembly and the protective cover.

Next, take out the instrument cluster socket and bulb assembly as needed.

Reverse the removal procedure to complete the process.

Remove the Instrument Cluster (IC).

Reverse the removal procedure.

Disconnect the electrical connector from the headlamp assembly, remove the HID bulb access cover, release the retainer, and then remove the headlamp bulb.

Handle it only by its base to avoid touching the glass envelope.

The headlamp bulb should not be removed until just before installing a replacement bulb, as prolonged exposure can affect performance due to contaminants entering the assembly.

Reverse the removal procedure to complete the installation.

Handle the bulb only by its base to avoid personal injury, as it contains gas under pressure and may shatter if the glass envelope is scratched or dropped.

Disconnect the electrical connector and remove the headlamp bulb.

Reverse the removal procedure to complete the installation.

Reverse the removal procedure.

Ensure not to touch the glass with your fingers.

Handle it only by its base to avoid personal injury, as it contains gas under pressure.

Handle it carefully, grip it by the base, and avoid touching the glass to prevent shattering.

Reverse the removal procedure to install the new bulb.

Exercise caution as the bulb contains gas under pressure, which may cause it to shatter if the glass envelope is scratched or if the bulb is dropped.

The halogen bulb contains gas under pressure, which may cause it to shatter if the glass envelope is scratched or if the bulb is dropped.

Release the spring retainer to separate the HID bulb from the headlamp assembly.

Remove the air cleaner intake pipe.

Ensure the headlamp switch and ignition switch are both in the OFF position.

Handle the bulb only by its base to avoid personal injury.

Bulbs 9004 and 9007 appear similar but are not interchangeable.

Remove the foglamp assembly.

It should not be removed until just before installing a new bulb.

Never turn on the headlamps with the bulb removed.

Handle the bulb carefully by grasping only its base and avoiding contact with the glass envelope to prevent personal injury.

Remove the four screws securing the low beam access cover, then remove the cover and seal. Next, remove the four screws from the ballast access cover, followed by the cover and seal. Unscrew the three ballast screws, disconnect the electrical connector, and remove the ballast.

The fog lamp bulb should not be removed until just before installing a new bulb to prevent performance issues due to contaminants.

The fog lamp bulb should not be removed until just before installing a new bulb to prevent contaminants from entering the assembly.

Take out the instrument cluster illumination bulbs.

Reverse the removal procedure.

Disconnect the electrical connector from the headlamp bulb.

Remove the 4 fender splash shield pin-type retainers and set the fender splash shield aside.

Prevent contaminants from entering the headlamp.

Disconnect the electrical connector and follow the same safety precautions as with the low beam bulb.

Remove the four fender splash shield bolts, tightening them to 5 Nm (44 lb-in) upon reinstallation, and then take out the four pin-type retainers to set the fender splash shield aside. Disconnect the fog lamp electrical connector, then squeeze both tabs on the fog lamp bulb simultaneously to remove it.

Simply reverse the removal procedure.

Avoid touching the glass envelope and refrain from removing the bulb for an extended period.

First, remove the instrument cluster.

Never turn on the headlamps with the bulb removed.

The bulb contains gas under pressure and may shatter if dropped or scratched, posing a risk of personal injury.

Rotate the bulb one quarter turn counterclockwise and lift it out from the IC.

Rotate it one quarter turn counterclockwise and lift it straight out from the instrument cluster.

Reverse the removal procedure and handle the halogen bulb only by its base.

Check the headlamp adjustment afterward.

Carefully rotate the bulb one-eighth turn counterclockwise to remove it.

Begin by removing the headlamp assembly.

Reverse the removal procedure, and if necessary, install new bulbs and adjust the headlamps accordingly.

Install the new bulb(s) by reversing the removal procedure.

Handle the bulb only by its base to avoid personal injury, as the bulb contains gas under pressure and may shatter if the glass envelope is scratched or dropped.