Ford E6DZ-13466-B
Tail Lamp Bulb, Rear Inner

The instrument cluster removal must be the first step when servicing the warning indicator bulb. To access the miniature bulb you should turn it counter-clockwise by a quarter turn followed by pulling it straight upward. The opposite steps need to be followed during bulb installation after service completion.

Begin service on the headlamp bulb by putting both the headlamp switch and ignition switch into their OFF positions. One can reach halogen bulbs through the engine compartment without dismantling the headlamp assembly but replacing HID bulbs demands full removal of the headlamp assembly. The service begins with unfastening the access cover of the headlamp bulb. The procedure requires counting one eighth rotation in the opposite direction for bulb removal and then disconnecting the electrical connector in each case. When installing a new bulb maintain contact only with its base because high internal pressure gas creates the risk for bulb shattering upon dropping or scratching. Take out the bulb only moments before configuration to stop contamination from entering the headlamp assembly which affects system functionality. To finish bulb replacement you should execute the installation steps in reverse order of removal.

Start the instrument cluster bulb servicing by removing the instrument cluster. Time to remove an illumination bulb starts with rotating it counterclockwise until it reaches one quarter turn and then pulling it upward from the instrument cluster. Perform the reverse order of removal steps to install the new bulb after it has been stripped from its position.

Starting the service of a fog lamp bulb requires you to switch both headlamps and ignition to OFF position. Place the vehicle in NEUTRAL mode and position it onto a hoist frame. Gently remove the fog lamp bulb by disconnecting its electrical connector while using bulb base handling only to prevent personal injury since the bulb contains high-pressure gas which can break on envelope scratches or drops. Handling of the glass envelope should be avoided while any prolonged exposure of the bulb outside the fog lamp assembly can degrade its performance through envelope contamination with foreign substances. Use the reverse steps to replace the new bulb into position after it becomes ready for installation.

Service of the fog light bulb requires turning off both the ignition switch and headlamp switch before beginning. Remove the front bumper cover after which you should disconnect the electrical connector and take out the fog lamp bulb. 5.4L vehicles need to be positioned in NEUTRAL on a hoist before removing the fog lamp bulb through its tabs and disconnecting the electrical connector. Reinstall the new bulb while following the steps in reverse order to installation. Proper handling of the fog lamp bulb demands base grasping while refraining from touching the enclosed glass since the bulb runs under pressured gas which might break when mishandled. Both installations must be done at the precise moment before installation to stop contaminants from damaging performance and fog lamps must stay off when any bulb is out of the device.

The service procedure for headlamp bulbs starts with disabling both headlamp switch and ignition switch. You should start your task by taking out the headlamp bulb access cover. When servicing the MKX headlamp bulb you should rotate it 1/8 turn to the left while counting the rotations and afterward detach the electrical connector. It is essential to handle new bulbs exclusively by their base during installation to protect the glass envelope because pressure gas inside the bulb could result in breakage from both glass scratches and also from manual drops. You must install the new bulb right away because putting off can let contaminants from entering the headlamp that might damage its functionality. The installation process can be finished after you reverse the removal steps.

The first requirement to service the left headlamp bulb is to switch off both the headlamp switch and ignition switch. The first step requires you to disconnect the air cleaner intake component. The next step involves removing the protective cover of the headlamp bulb followed by disconnecting its electrical connector to extract the headlamp bulb. Finger the bulb base to keep away from the glass envelope because pressure-filled gas inside makes the bulb break if you touch it and causes possible harm. Safety requires users to not take out the bulb for long durations due to potential contamination threats which could degrade headlamp functionality. Installation of the new bulb requires following the removal procedure in reverse order by completely sealing the protective cover.

One starts bulb warning indicator maintenance by removing the instrument cluster through extraction of seven screws along with the instrument cluster shield. To extract warning indicator bulbs the user should turn them counterclockwise one quarter revolution before lifting them out from the instrument cluster. You should put warning indicator bulbs back after you have removed them by completing the reverse steps of removal.

Service of the fog lamp bulb begins with turning off both the headlamp switch and ignition switch before proceeding. Loosen the transmission by setting the vehicle into neutral then mount it onto the hoist for work. To access the base fog lamp bulb drivers must rotate it by one-eighth turn counterclockwise before disconnecting the electrical connector. Vehicles with the Adrenalin package fog lamp require the user to squeeze the tabs and pull the fog lamp bulb from the assembly before disconnecting the electrical connector. Touching the bulb base represents the only safe method to handle it because the gas-filled bulb becomes hazardous when you drop or scratch the glass envelope. Performance of the assembly may suffer from contaminants so fog lamp bulbs need to be removed for replacement only immediately before installation. Reattach the new bulb by performing the opposite actions to bulb removal.

Start the instrument cluster bulb servicing by removing the instrument cluster. Time to remove an illumination bulb starts with rotating it counterclockwise until it reaches one quarter turn and then pulling it upward from the instrument cluster. Perform the reverse order of removal steps to install the new bulb after it has been stripped from its position.

The first step to service the instrument panel bulb requires removal of the Instrument Cluster (IC). The illumination bulb can be removed by counterclockwise rotation followed by lifting it out of the IC. You should replace the removed illumination bulb(s) using the steps in reverse order to put them in.

Rotate it one quarter turn counterclockwise and lift it out from the instrument cluster.

Never turn on the headlamps with the bulb removed.

Reverse the removal procedure.

Ensure the headlamp switch and ignition switch are in the OFF position.

Handle the bulb only by its base to avoid personal injury, as it contains gas under pressure and may shatter if dropped or scratched. Avoid touching the glass envelope.

The headlamp bulb should only be handled by its base.

Reverse the removal procedure.

First, remove the selector lever assembly.

Reverse the removal procedure, handling the new halogen bulb carefully.

The headlamp bulb should not be removed from the assembly until just before installing a new bulb to prevent performance issues caused by contaminants entering the assembly.

Rotate the bulb approximately one-eighth turn counterclockwise to remove it, then disconnect the electrical connector.

Rotate it one quarter turn counterclockwise and lift it out from the instrument cluster.

The vehicle should be in NEUTRAL and positioned on a hoist.

Disconnect the electrical connector.

Ensure the headlamp switch and ignition switch are both in the OFF position.

Rotate the headlamp bulb one-eighth turn counterclockwise to detach it.

Remove the instrument cluster (IC).

Reverse the removal procedure to install the new bulb.

The vehicle should be in NEUTRAL and positioned on a hoist.

Handle the bulb carefully, only by its base, to avoid personal injury.

Disconnect the electrical connector from the bulb.

Simply reverse the removal procedure.

Rotate the bulb counterclockwise approximately one-eighth turn, disconnect the electrical connector, and take out the bulb.

Reverse the removal procedure.

Install the new one by reversing the removal procedure.

Never turn on the headlamps.

Begin by removing the headlamp assembly.

The LH headlamp bulb is accessible directly.

Carefully disconnect the electrical connector.

Reverse the removal procedure, ensuring that the headlamp bulb protective cover is completely sealed.

The bulb contains gas under pressure and may shatter if mishandled.

Rotate the headlamp bulb counterclockwise approximately one-eighth turn to remove it.

The bulb contains gas under pressure and may shatter if the glass envelope is scratched or dropped.

Ensure the headlamp switch and ignition switch are both in the OFF position.

Raise and support the vehicle.

Extended removal may allow contaminants to enter the headlamp and settle on the lens and reflector, affecting performance.

It can affect the bulb's performance due to potential contaminants entering the fog lamp.

Remove the headlamp bulb access cover.

Disconnect the headlamp bulb electrical connector, then rotate the bulb approximately one-eighth turn counterclockwise to remove it from the headlamp assembly.

Rotate the headlamp bulb retaining ring counterclockwise to remove it.

Ensure the headlamp and ignition switches are in the OFF position.

Rotate the bulb one quarter turn counterclockwise and lift it out from the instrument cluster.

Reverse the removal procedure, ensuring that for vehicles with HID headlamps, the bulb cover is fully seated.

Handle the bulb only by its base and avoid touching the glass envelope.

Reverse the removal procedure.

Turn the collar counterclockwise one-eighth of a turn and remove it, followed by turning the seal beam one-eighth of a turn and removing it.

Disconnect the headlamp bulb electrical connector.

Turn the collar counterclockwise one-eighth of a turn and remove it, then turn the seal beam one-eighth of a turn to detach it.

Never turn on the headlamps with the bulb removed.

Ensure the headlamp switch and ignition switch are both in the OFF position.

Rotate the bulb one quarter turn counterclockwise and lift it out from the IC.

Install the new bulb immediately to prevent contaminants from entering the headlamp assembly.

Remove the headlamp bulb protective cover and the headlamp bulb itself by disconnecting the electrical connector.

Rotate the headlamp bulb approximately 1/8 turn counterclockwise.

The bulb contains gas under pressure and may shatter if the glass envelope is scratched or dropped.

Remove the engine appearance cover, then the bolt and the windshield washer reservoir filler tube.

Reverse the removal procedure to complete the process.

One of the base instrument clusters is shown, and other instrument clusters are similar.

Reverse the removal procedure, ensuring not to turn on the fog lamps with the bulb removed from the assembly.

Remove the two screws securing the headlamp bulb and disconnect the electrical connector.

Extended exposure can affect performance due to contaminants entering the headlamp and settling on the lens and reflector.

The headlamp bulb should only be removed just before installing a new one to prevent performance issues caused by contaminants entering the headlamp.

Never turn on the headlamps with the bulb removed.

Avoid touching the glass envelope and do not remove the bulb from the assembly until just before installation to prevent contaminants from affecting performance.

It may affect headlamp bulb performance and allow contaminants to enter the headlamp.

Do not turn on the fog lamps with the bulb removed, as contaminants may affect performance.

Carefully take out the headlamp bulb, handling it only by its base to avoid contact with the glass envelope.

Reverse the removal procedure.

Remove the aeroshield-to-sub frame screws and the seven screws securing the aeroshield, then take off the aeroshield.

The vehicle should be in NEUTRAL and positioned on a hoist.

Reverse the removal procedure.

Ensure the headlamp switch and ignition switch are turned off.

Handle the bulb only by its base to avoid personal injury.

First, remove the instrument cluster.

Take off the headlamp bulb protective cover and disconnect the electrical connector to remove the headlamp bulb.

Reverse the removal procedure.

Install the new bulb by reversing the removal procedure.

Avoid removing the bulb for an extended period, as this can affect performance and allow contaminants to enter the headlamp assembly.

Rotate it one quarter turn counterclockwise and lift it out from the instrument cluster.

Rotate the headlamp bulb one-eighth turn counterclockwise to detach it.

Ensure the headlamp assembly electrical connector is disconnected to avoid high voltage hazards.

Rotate the headlamp bulb retaining ring counterclockwise to remove it.

Never turn on the headlamps with the bulb removed.

Disconnect the electrical connector from the fog lamp assembly and carefully remove the fog lamp bulb.

The bulb contains gas under pressure and may shatter if the glass envelope is scratched or dropped.

Ensure the headlamp switch and ignition switch are both in the OFF position.

Reverse the removal procedure.

The vehicle should be in NEUTRAL and positioned on a hoist.

Carefully disconnect the electrical connector.

The headlamp bulb should remain in place until just before the new bulb is installed.

To prevent contaminants from entering and affecting performance, and to avoid damaging the bulb.

Remove the instrument cluster.

Handle the bulb carefully, grip it by the base, and avoid touching the glass to prevent shattering.