Ford F1DZ-10C359-A
Voltage Regulator

Service of the voltage regulator requires generator removal and subsequent steps of removing the generator brush device and terminal holder before performing work on the regulator. The generator brush and terminal holder must be separated from the voltage regulator through screw cap removal and screw disassembly. After positioning the brush and terminal holder on the voltage regulator please secure it through screws while keeping the screw cap over Test Terminal A to prevent shorting the B+ battery connection. Install the generator brush and terminal holder and voltage regulator while depressing the brushes for insertion with a wire to keep them in position. Place all components correctly while securing screws before taking out the wire. Finally, reinstall the generator.

Service of the voltage regulator requires generator removal and subsequent steps of removing the generator brush device and terminal holder before performing work on the regulator. The generator brush and terminal holder must be separated from the voltage regulator through screw cap removal and screw disassembly. After positioning the brush and terminal holder on the voltage regulator please secure it through screws while keeping the screw cap over Test Terminal A to prevent shorting the B+ battery connection. Install the generator brush and terminal holder and voltage regulator while depressing the brushes for insertion with a wire to keep them in position. Place all components correctly while securing screws before taking out the wire. Finally, reinstall the generator.

Service and repair operations on the voltage regulator begin with generator removal. Service and repair of the voltage regulator begins by first removing the generator followed by taking out the generator brush and terminal holder by unscrewing their attaching hardware. Drilling the screw cap and screws enables separation of the generator brush from the voltage regulator terminal holder. Start by positioning the brush and terminal holder on the voltage regulator before installing its screws as well as screw cap to ensure Test Terminal A has the screw cap properly sealed due to its role in preventing battery positive (B+) shorting. Depress the generator brushes before you place them with the terminal holder next to the voltage regulator. Then secure the position by inserting a wire for the brushes. Place the components on position while installing screws afterward removing the wire. Finally, reinstall the generator.

The composite of generator brush and terminal holder and voltage regulator must be installed at once. Maintenance on this assembly starts with disassembly of the generator. The first step requires you to remove the screws from both the generator brush and terminal holder and voltage regulator assembly before gently extracting the complete assembly. Brushes should be compressed when you put the wire inside to maintain their position throughout the installation. The generator brush must be installed along with the terminal holder together with the voltage regulator assembly before securing it using screws followed by taking out the wire supporting the brushes.

The first step to service and repair the voltage regulator involves generator removal using appropriate alternator procedures. You must eliminate the generator brush together with terminal holder and voltage regulator after unscrewing them. The generator brush must be detached from its terminal holder when separating it from the voltage regulator through screw cap removal and loose of screws. The installation process starts by setting up the brush and terminal holder on the voltage regulator but includes screwing in the components while making sure the screw cap covers Test Terminal A because this stops contact between the battery positive (B+) and unintentional shorting. To finish the installation depress the brushes and insert a wire to secure them before installing the generator brush and terminal holder with the voltage regulator. Align all components correctly and fasten screws before eliminating the wire from its position. Finally, reinstall the generator.

The repair process for the voltage regulator begins with generator removal but this procedure only works for gasoline generators because 7.3L diesel engines possess a regulated generator inside their system. Start by removing the four screws that secure the voltage regulator while proceeding to separate both the generator brush and terminal holder. Separating the generator brush and terminal holder from the voltage regulator requires removing the screw cap together with the two screws fastening the brush and terminal holder. The installation process begins with placing the brush and terminal holder onto the voltage regulator then fastening with screws and putting back the screw cap which must cover Test Terminal A so the battery positive connection does not get shorted. Depress the brushes and add a wire for stabilizing them before putting in the generator brush with the terminal holder and voltage regulator set-up. Once the voltage regulator is installed, remove the wire without losing its position and complete the installation. Finally, reinstall the generator.

The first task for servicing or repairing the voltage regulator involves removing the generator from its location. Start by unfastening all screws that secure the generator brush and terminal holder as well as the voltage regulator assembly. You should start the installation process by pressing down the brushes while installing wires to maintain position for generator brush and terminal holder and voltage regulator assembly assembly. Install the screws afterward but first remove the wire from the secured assembly. Finally, reinstall the generator.

You should start by taking off the generator after making note of this repair process's restriction to gas engines since diesel generators have built-in internal regulators which cannot be serviced independently. You must detach the generator brush and terminal holder along with the voltage regulator by removing the four screws on the voltage regulator. To isolate the generator brush and terminal holder from the voltage regulator proceed by unscrewing the screw cap and subsequently removing the two screws attaching the generator brush and terminal holder. Position the brush and terminal holder correctly on the voltage regulator before installing generator brush and terminal holder screws and placing the screw cap making sure it covers Test Terminal A to avoid battery positive connection shorting. Reinstall all pieces by using a wire to compress the brush while you restore the generator brush and terminal holder following the voltage regulator. To finish the installation you must place the generator brush and terminal holder and the voltage regulator while installing its screws afterward you need to remove the wire before reinserting the generator.

Starting service and repair of the voltage regulator involves generator removal first. One should begin by removing the generator brush and terminal holder and voltage regulator assembly through screw removal. Start with brush depression until you can insert a wire to maintain their position while carrying out the installation steps. You need to install the generator brush and terminal holder before securing it with screws along with the voltage regulator assembly. Afterward you should take out the wire. Finally, reinstall the generator.

The service procedure for voltage regulator consists of removing the generator then the generator brush and terminal holder with the voltage regulator assembly using correct screw removal. After inserting the wire to depress the brushes, install the generator brush with terminal holder together with the voltage regulator assembly while fastening with screws before removing the wire. Finally, reinstall the generator.

Service operations need to be performed on the voltage regulator and brush holder unit together. First remove the generator component followed by taking out the regulator and brush holder by removing their screws. The new generator regulator and brush holder should be installed while pressing down on the brushes before you insert your wire as a holding mechanism. After securing both the regulator and brush holder properly install their screws then remove the positioning wire. Finally, reinstall the generator. Vehicle relearning requires you to drive 16 km (10 miles) or more after disconnecting and reconnecting the battery since the adaptive strategy needs time to complete the relearning process.

The first step to work on the voltage regulator involves removing the generator unit. The necessary screws should be unscrewed to remove the generator brush and terminal holder (part A) with the voltage regulator assembly (part B). The first step for installation should be to install the generator brush and terminal holder (part A) and the voltage regulator assembly (part B). Place the brushes (part C) flat against the surface before using part D wires to maintain brush position while installing. To install the generator brush and terminal holder (part A) and voltage regulator assembly (part B) secure first the screws then take away part D which is the wire. Finally, reinstall the generator.

The first step for servicing or repairing the gasoline-engine generator voltage regulator requires removal of the generator itself. Unscrew the four voltage regulator screws to remove it together with the terminal holder and generator brush from the device. You need to disconnect the generator brush and terminal holder from the voltage regulator through the removal of its screw cap followed by unscrewing the two screws which stabilize the generator brush and terminal holder. Set the brush and terminal holder on the voltage regulator next then fasten it with both generator brush and terminal holder screws for installation. Test Terminal A requires the attachment of the screw cap to stop any possible short circuit involving the battery positive charge. Press the brushes before inserting a wire for support when installing the generator brush and terminal holder and the voltage regulator. Position the components first and install the voltage regulator screws before removing the wire. Finally, reinstall the generator.

The voltage regulator service demands generator removal as the first step. The next procedure requires removal of four screws that hold the generator voltage regulator assembly together with its generator brush and terminal holder. The assembly of the voltage regulator requires tightening the screws to 3 Nm while using 27 lb-in torque measurement. Before generator brush assembly it is critical to insert a wire specifically plastic into the holding wire insertion hole of the brush to keep the generators stacks properly aligned. The correct generator operation requires users to remove the wire just before starting their vehicle. The last step ends the installation process by performing the reverse action of removal.

Service of the voltage regulator requires generator removal before beginning the work. The first step involves removing generator brushes and terminal holders together with the voltage regulator assembly using screw removal. During installation you should first compress the brushes as you put in a wire that will maintain their position during the procedure. After securing the generator brush together with terminal holder you can place the voltage regulator assembly along with screws before you remove the wire. The installation process ends with generator reinstallation.

Depress the (A) brushes and insert the (B) wire to hold the brushes in place for installation.

Take out the generator brush terminal holder and the voltage regulator assembly by unscrewing the screws and removing the assembly.

Next, depress the brushes and insert a wire to hold the brushes in place during installation.

Take out the voltage regulator/brush holder assembly by removing the screws.

Next, take out the generator brush and terminal holder, along with the voltage regulator assembly by unscrewing the necessary screws.

Press the brushes and insert a wire to hold them during the installation process.

Reverse the removal procedure.

Depress the brushes and insert a wire to hold them in place.