How to service the Yaw Sensor within the stability control sensor cluster on Ford Expedition?

Service of the yaw rate sensor in the stability control sensor cluster starts with eliminating the front floor console. You should detach the stability control sensor cluster while removing its two mounting bolts before disconnecting the electrical connector. Installation of the new sensor requires you to perform the opposite steps of removal. All three components of lateral accelerometer and longitudinal accelerometer and roll rate sensor function as one integral unit inside the yaw rate sensor and stability control sensor cluster.

How to Service and Repair the Yaw Sensor on Ford Explorer?

The first step for yaw rate sensor maintenance requires removal of the pin-type retainer along with the left-hand floor console finish panel. The left-hand instrument panel brace requires removal of its two bolts and two nuts before installation where you must use 9 Nm (80 lb-in) torque setting. You should first disconnect the electrical connector from the stability control sensor cluster then remove two floor heater duct bolts on the left side. Disassemble each electrical harness retainer connected to the stability control sensor cluster and place the parts to the side. Loosen the two stability control sensor cluster bracket nuts to access the stability control sensor cluster which should be removed before reinstallation by securing the nuts to 7 Nm (62 lb-in). The installation ends with performing the steps in reverse order to ensure all components are tightly implemented. The installation of new stability control sensor clusters requires ABS module calibration through scan tool instructions.

OEM Ford Yaw Sensor

Yaw Rate Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Yaw Sensors found

View related parts
Ford Yaw Rate Sensor Part Number: 7C2Z-3C187-A
Product Specifications
- Other Name: Sensor Assembly; Suspension Yaw Sensor; Sensor
- Manufacturer Note: Sensor - Yaw
- Replaces: 6C2Z-3C187-AA
Fits the following Ford Models:
- E-150 | 2008-2010 | Base, XL, XLT | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG
- E-250 | 2008-2010 | Base | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG
- E-350 Super Duty | 2008-2010 | Base, XL, XLT | 10 Cyl 6.8 L CNG, 10 Cyl 6.8 L GAS, 10 Cyl 6.8 L LPG, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG, 8 Cyl 6.0 L DIESEL
View More
View related parts
Ford Sensor Part Number: 3L1Z-3C187-AA
Product Specifications
- Other Name: Sensor Assembly; ABS Deceleration Sensor; ABS Sensor
- Manufacturer Note: Lateral/Yaw Sensor
- Replaces: 2C5Z-3C187-AB
Fits the following Ford Models:
- Expedition | 2003-2006 | Eddie Bauer, King Ranch, Limited, NBX, XLS, XLT, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Yaw Rate Sensor Part Number: 8L8Z-3C187-A
Product Specifications
- Other Name: Sensor Assembly; Yaw Sensor; Sensor
Fits the following Ford Models:
- Escape | 2008-2011 | Limited, XLS, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Yaw Rate Sensor Part Number: 7L1Z-3C187-A
Product Specifications
- Other Name: Sensor Assembly; Suspension Yaw Sensor; Steering Wheel Speed Sensor; Yaw Sensor; Sensor
- Manufacturer Note: Lateral/Yaw Sensor
Fits the following Ford Models:
- Expedition | 2007-2010 | Eddie Bauer, EL Eddie Bauer, EL King Ranch, EL Limited, EL XLT, Funkmaster Flex Edition, King Ranch, Limited, XLT | 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
- Explorer | 2007-2010 | Eddie Bauer, Limited, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
- Explorer Sport Trac | 2007-2010 | Limited, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View More
View related parts
Ford Sensor Part Number: YS4Z-14B296-AA
Product Specifications
- Other Name: Sensor Assembly; ABS Sensor
- Manufacturer Note: Also supplied in 3C187.
Fits the following Ford Models:
- Focus | 2000-2004 | LX, SE, Sony Limited Edition, SVT, ZTS, ZTW, ZX3, ZX5 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Yaw Rate Sensor Part Number: 9S4Z-3C187-B
Product Specifications
- Other Name: Sensor Assembly; Suspension Yaw Sensor; Yaw Sensor
- Replaces: 9S4Z-3C187-A
Fits the following Ford Models:
- Focus | 2008-2011 | S, SE, SEL, SES | 4 Cyl 2.0 L GAS
View related parts
Ford Yaw Rate Sensor Part Number: 8G1Z-3C187-A
Product Specifications
- Other Name: Sensor Assembly; Suspension Yaw Sensor; Yaw Sensor
- Manufacturer Note: Sensor - Yaw
Fits the following Ford Models:
- Police Interceptor Sedan | 2013-2019 | Base | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L FLEX, 6 Cyl 3.7 L GAS
- Special Service Police Sedan | 2014-2018 | Base | 4 Cyl 2.0 L GAS
- Taurus | 2008-2019 | Limited, SE, SEL, SHO | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
- Taurus X | 2008-2009 | Eddie Bauer, Limited, SEL | 6 Cyl 3.5 L GAS
View More
View related parts
Ford Yaw Rate Sensor Part Number: 8A8Z-3C187-A
Product Specifications
- Other Name: Sensor Assembly; Yaw Sensor
Fits the following Ford Models:
- Flex | 2009 | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Yaw Rate Sensor Part Number: 6G9Z-14B296-A
Product Specifications
- Other Name: Sensor Assembly; ABS Deceleration Sensor; ABS Sensor; Sensor
Fits the following Ford Models:
- Transit Connect | 2010-2013 | XL, XLT, XLT Premium | 4 Cyl 2.0 L GAS
View related parts
Ford Yaw Rate Sensor Part Number: 7T4Z-3C187-A
Product Specifications
- Other Name: Sensor Assembly; Suspension Yaw Sensor; Yaw Sensor
- Manufacturer Note: Sensor - Yaw
Fits the following Ford Models:
- Edge | 2007-2010 | Limited, SE, SEL, SEL Plus, Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Yaw Rate Sensor Part Number: 6L2Z-3C187-AA
Product Specifications
- Other Name: Sensor Assembly; Suspension Yaw Sensor; Steering Wheel Speed Sensor; Yaw Sensor; Sensor
- Manufacturer Note: Lateral/Yaw Sensor
- Replaces: 3C5Z-3C187-AB
Fits the following Ford Models:
- Expedition | 2007 | Eddie Bauer, EL Eddie Bauer, EL Limited, EL XLT, Limited, XLT | 8 Cyl 5.4 L GAS
- Explorer | 2004-2007 | Eddie Bauer, Limited, NBX, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
- Explorer Sport Trac | 2007 | Limited, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View More
View related parts
Ford Yaw Rate Sensor Part Number: 3L2Z-3C296-BA
Product Specifications
- Other Name: Sensor Assembly
- Manufacturer Note: Sensor - Yaw
Fits the following Ford Models:
- Explorer | 2002-2005 | Eddie Bauer, Limited, NBX, Postal, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Sensor Part Number: 3L2Z-3C187-AA
Product Specifications
- Other Name: Sensor Assembly; ABS Deceleration Sensor; Suspension Yaw Sensor; Steering Wheel Speed Sensor
Fits the following Ford Models:
- Expedition | 2003 | Eddie Bauer, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
- Explorer | 2002-2003 | Eddie Bauer, Limited, XLS, XLT | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Sensor Part Number: 2M5Z-3C187-AD
Product Specifications
- Other Name: Sensor Assembly; ABS Sensor
Fits the following Ford Models:
- Focus | 2002-2007 | LX, S, SE, SES, ST, SVT, ZTS, ZTW, ZX3, ZX4, ZX4 ST, ZX5, ZXW | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Sensor Part Number: 2L1Z-3C296-BA
Product Specifications
- Other Name: Sensor Assembly; ABS Deceleration Sensor; ABS Sensor
Fits the following Ford Models:
- Expedition | 2003 | Eddie Bauer, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Yaw Rate Sensor Part Number: 3L2Z-3C296-AA
Product Specifications
- Other Name: Sensor Assembly
- Manufacturer Note: Sensor - Yaw
Fits the following Ford Models:
- Explorer | 2002-2005 | Eddie Bauer, Limited, NBX, Postal, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Sensor Part Number: 2L1Z-3C296-AA
Product Specifications
- Other Name: Sensor Assembly; ABS Deceleration Sensor; ABS Sensor
Fits the following Ford Models:
- Expedition | 2003 | Eddie Bauer, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS

Ford Yaw Sensor

OEM Yaw Sensor boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Yaw Sensor with long life and a perfect fit. Come to our website and find genuine Ford parts. We keep a wide inventory of OEM parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Ford Yaw Sensor Parts and Q&A

Sensor
3L1Z-3C187-AA
Q: How to service the Yaw Sensor within the stability control sensor cluster on Ford Expedition?
A:
Service of the yaw rate sensor in the stability control sensor cluster starts with eliminating the front floor console. You should detach the stability control sensor cluster while removing its two mounting bolts before disconnecting the electrical connector. Installation of the new sensor requires you to perform the opposite steps of removal. All three components of lateral accelerometer and longitudinal accelerometer and roll rate sensor function as one integral unit inside the yaw rate sensor and stability control sensor cluster.
Yaw Rate Sensor
7L1Z-3C187-A
Q: How to Service and Repair the Yaw Sensor on Ford Explorer?
A:
The first step for yaw rate sensor maintenance requires removal of the pin-type retainer along with the left-hand floor console finish panel. The left-hand instrument panel brace requires removal of its two bolts and two nuts before installation where you must use 9 Nm (80 lb-in) torque setting. You should first disconnect the electrical connector from the stability control sensor cluster then remove two floor heater duct bolts on the left side. Disassemble each electrical harness retainer connected to the stability control sensor cluster and place the parts to the side. Loosen the two stability control sensor cluster bracket nuts to access the stability control sensor cluster which should be removed before reinstallation by securing the nuts to 7 Nm (62 lb-in). The installation ends with performing the steps in reverse order to ensure all components are tightly implemented. The installation of new stability control sensor clusters requires ABS module calibration through scan tool instructions.