How to service and repair the Tie Rod on Lincoln Navigator?

A substantial step before servicing or repairing the toe link is to deactivate the air suspension system by disabling the air suspension switch positioned in the LH rear quarter trim panel because skipping this procedure can trigger unexpected air spring inflation or deflation that produces vehicle movement. Start the procedure by taking off the wheel together with the tire component. The hex holding feature should be used before removing the nut so the stud stays stationary before the toe link needs to be removed from the wheel knuckle. The second step involves unstowing the toe link and the nut from the system. To install the system follow the opposite order of steps from removal and inspect and adjust the rear toe if required.

How to service and repair the inner tie rod on Lincoln Town Car?

The servicing and repair of inner tie rod starts with wheel removal and tire detachment followed by loosening the tie-rod jam nut until you tighten it to 55 Nm (41 lb-ft) torque during reinstallation. A hex holding feature must be used to stop the stud from turning when taking out the nut and the outer tie-rod end should be detached from the wheel knuckle using a torque setting of 80 Nm (59 lb-ft). Write down the number of outer tie-rod end turns as they will be needed during reassembly before you remove this component. First disconnect the tie-rod jam nut then for those who need to fix the right-side inner tie rod it becomes essential to stretch the bellows boot on the left-side for steering gear control. Detach both clamps from the bellows boot while taking off the boot itself. The steering gear must be set at center position while using an appropriate crowfoot wrench to secure the rack gear flat area when installing the inner tie rod. Tighten this rod to 100 Nm (74 lb-ft) torque specifications after installation. The removal of abrasive material should be complete because it can cause damage to the steering gear while avoiding twists of the bellows boot for protection. The inner tie-rod groove should receive an application of grease before the bellows boot placement while ensuring appropriate positioning on the steering gear housing bead and inside the inner tie-rod channel. The procedure for removal inversion leads to part cleaning for reusable components before new part installation. Checking and readjusting the front toe completes the procedure.

OEM Lincoln Tie Rod

Steering Tie Rod

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

40 Tie Rods found

View related parts
Lincoln Outer Tie Rod Part Number: 2W7Z-3A130-A
$33.79 MSRP: $46.74
You Save: $12.95 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting
Fits the following Lincoln Models:
- Continental | 1985-1987 | Base, Givenchy, Valentino | 8 Cyl 5.0 L GAS
- Town Car | 1984-2002 | Anniversary, Base, Cartier, Cartier L, Cypress, Executive, Executive L, Jack Nicklaus, Signature, Signature SE, Touring Edition, Tournament Edition | 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
View related parts
Lincoln Inner Tie Rod Part Number: 2L1Z-3280-GA
$50.04 MSRP: $79.45
You Save: $29.41 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rod; Steering Tie Rod End, Inner; Inner Tie Rod End; Tie Rod End
- Manufacturer Note: When Replacing Inner Tie Rods, Use Boots & Clamps Listed To Ensure A Proper Seal And Minimize Contamination
- Position: Inner
- Replaces: 2L1Z-3280-FA
Fits the following Lincoln Models:
- Navigator | 2003-2006 | Base, Luxury, Ultimate | 8 Cyl 5.4 L GAS
View related parts
Lincoln Inner Tie Rod Part Number: GG1Z-3280-A
$48.62 MSRP: $80.00
You Save: $31.38 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Tie Rod; Steering Tie Rod End, Inner
- Position: Inner
- Replaces: GG1Z-3280-B, MEF-342
Fits the following Lincoln Models:
- MKT | 2016-2019 | Base, EcoBoost, Livery, Premiere, Reserve | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln Inner Tie Rod Part Number: AA8Z-3280-B
$35.27 MSRP: $56.00
You Save: $20.73 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rod; Steering Tie Rod End, Inner; Inner Tie Rod End; Tie Rod End
- Position: Inner
- Replaces: AA5Z-3280-A, 8A5Z-3280-A, AA8Z-3280-A
Fits the following Lincoln Models:
- MKS | 2009-2012 | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
- MKT | 2010-2012 | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln Inner Tie Rod, Passenger Side Part Number: 2L3Z-3A130-DA
$47.74 MSRP: $80.00
You Save: $32.26 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting; Steering Tie Rod End, Right Inner; Outer Tie Rod End; Tie Rod End
- Position: Inner Passenger Side
- Replaces: F65Z-3A130-DA
Fits the following Lincoln Models:
- Navigator | 1998-2002 | Base | 8 Cyl 5.4 L GAS
View related parts
Lincoln Inner Tie Rod, Driver Side Part Number: 2L3Z-3A131-BA
$61.88 MSRP: $101.82
You Save: $39.94 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting; Steering Tie Rod End, Left Inner; Outer Tie Rod End; Tie Rod End
- Position: Inner Driver Side
- Replaces: F65Z-3A130-BB
Fits the following Lincoln Models:
- Navigator | 1998-2002 | Base | 8 Cyl 5.4 L GAS
View related parts
Lincoln Tie Rod End, Outer Passenger Side Part Number: LX6Z-3A130-A
$47.77 MSRP: $74.55
You Save: $26.78 (36%)
ADD TO CART
Product Specifications
- Other Name: Rod - Tie; Steering Tie Rod End, Right Outer; Steering Tie Rod End; Outer Tie Rod End; Outer Tie Rod
- Position: Outer Passenger Side
Fits the following Lincoln Models:
- Corsair | 2020-2023 | Base, Grand Touring, Reserve | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Lincoln Tie Rod Part Number: L1MZ-3280-F
$65.49 MSRP: $104.00
You Save: $38.51 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Tie Rod; Inner Tie Rod
- Replaces: L1MZ-3280-C, MEF-544
Fits the following Lincoln Models:
- Aviator | 2020-2023 | Base, Black Label, Black Label Grand Touring, Grand Touring, Livery, Reserve | 6 Cyl 3.0 L GAS, 6 Cyl 3.0 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Lincoln Outer Tie Rod, Driver Side Part Number: ML3Z-3A130-B
$73.64 MSRP: $123.64
You Save: $50.00 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting; Steering Tie Rod End, Left Outer; Outer Tie Rod End; Tie Rod End
- Position: Outer Driver Side
Fits the following Lincoln Models:
- Navigator | 2022-2024 | Base, Black Label, L Base, L Black Label, L Livery, L Reserve, Reserve | 6 Cyl 3.5 L GAS
View related parts
Lincoln Outer Tie Rod Part Number: R1MZ-3A130-D
$66.18 MSRP: $105.09
You Save: $38.91 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting
- Replaces: MEF-533, L1MZ-3A130-A
Fits the following Lincoln Models:
- Aviator | 2020-2023 | Base, Black Label, Black Label Grand Touring, Grand Touring, Livery, Reserve | 6 Cyl 3.0 L GAS, 6 Cyl 3.0 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Lincoln Inner Tie Rod Part Number: 6L3Z-3280-A
$49.26 MSRP: $82.55
You Save: $33.29 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rod; Steering Tie Rod End, Inner; Inner Tie Rod End; Tie Rod End
- Manufacturer Note: When Replacing Inner Tie Rods, Use Boots & Clamps Listed To Ensure A Proper Seal And Minimize Contamination
- Position: Inner
- Replaces: 4L3Z-3280-CA
Fits the following Lincoln Models:
- Mark LT | 2006-2008 | Base | 8 Cyl 5.4 L GAS
View related parts
Lincoln Inner Tie Rod Part Number: DP5Z-3280-A
$43.17 MSRP: $68.55
You Save: $25.38 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Tie Rod; Inner Tie Rod End; Tie Rod End
Fits the following Lincoln Models:
- Continental | 2017-2020 | 80th Anniversary Coach Door Edition, Base, Black Label, Coach Door Edition, Livery, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.7 L GAS
- MKZ | 2013-2020 | Base, Black Label, Black Label Hybrid, Hybrid, Premiere, Premiere Hybrid, Reserve, Reserve Hybrid, Reserve I, Reserve I Hybrid, Reserve II, Reserve II Hybrid, Select, Select Hybrid | 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln Inner Tie Rod Part Number: F2GZ-3280-A
$80.25 MSRP: $134.73
You Save: $54.48 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Tie Rod; Inner Tie Rod End; Tie Rod End
Fits the following Lincoln Models:
- MKX | 2016-2018 | Black Label, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS, 6 Cyl 3.7 L GAS
- Nautilus | 2019-2023 | Base, Black Label, Reserve, Select | 4 Cyl 2.0 L GAS, 6 Cyl 2.7 L GAS
View related parts
Lincoln Inner Tie Rod, Driver Side Part Number: 2L3Z-3A131-AA
$34.73 MSRP: $56.73
You Save: $22.00 (39%)
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting; Steering Tie Rod End, Left, Left Inner; Outer Tie Rod End; Tie Rod End
- Position: Driver Side
- Replaces: F65Z-3A130-AB
Fits the following Lincoln Models:
- Blackwood | 2002 | Base | 8 Cyl 5.4 L GAS
- Navigator | 1998-2002 | Base | 8 Cyl 5.4 L GAS
View related parts
Lincoln Inner Tie Rod Part Number: LX6Z-3280-B
$45.55 MSRP: $71.09
You Save: $25.54 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rod Assembly - Spindle Connecting; Steering Tie Rod End, Inner
- Position: Inner
Fits the following Lincoln Models:
- Corsair | 2020-2023 | Base, Grand Touring, Reserve | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Lincoln Inner Tie Rod Part Number: L1MZ-3280-D
$64.69 MSRP: $102.73
You Save: $38.04 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rod
Fits the following Lincoln Models:
- Aviator | 2020-2023 | Base, Black Label, Black Label Grand Touring, Grand Touring, Livery, Reserve | 6 Cyl 3.0 L GAS, 6 Cyl 3.0 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Lincoln Inner Tie Rod Part Number: NL1Z-3280-A
$138.55 MSRP: $201.67
You Save: $63.12 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Tie Rod; Steering Tie Rod End, Inner
- Position: Inner
Fits the following Lincoln Models:
- Navigator | 2022-2024 | Base, Black Label, L Base, L Black Label, L Livery, L Reserve, Reserve | 6 Cyl 3.5 L GAS
View related parts
Lincoln Inner Tie Rod, Driver Side Part Number: XW4Z-3A131-CA
$71.94 MSRP: $99.52
You Save: $27.58 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rod; Steering Tie Rod End, Left Inner; Inner Tie Rod End; Tie Rod End
- Position: Inner Driver Side
Fits the following Lincoln Models:
- LS | 2000-2002 | Base, LSE | 6 Cyl 3.0 L GAS, 8 Cyl 3.9 L GAS
View related parts
Lincoln Inner Tie Rod Part Number: 2C5Z-3280-AA
$35.16 MSRP: $48.64
You Save: $13.48 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rod; Inner Tie Rod End; Tie Rod End
- Manufacturer Note: When Replacing Inner Tie Rods, Use Boots & Clamps Listed To Ensure A Proper Seal And Minimize Contamination
Fits the following Lincoln Models:
- Aviator | 2003-2005 | Base | 8 Cyl 4.6 L GAS
View related parts
Lincoln Outer Tie Rod Part Number: 1F3Z-3A130-A
$44.64 MSRP: $60.75
You Save: $16.11 (27%)
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting; Steering Tie Rod End; Outer Tie Rod End; Tie Rod End
- Replaces: F5OY-3A130-A
Fits the following Lincoln Models:
- Continental | 1995-2002 | Anniversary, Base, Diamond Anniversary, Signature, Spinnaker Edition | 8 Cyl 4.6 L GAS

| Page 1 of 2 |Next >

1-20 of 40 Results

Lincoln Tie Rod

If you own Lincoln and want to keep it in top shape, choosing OEM Tie Rod is a smart move. They are precisely engineered and follow strict factory standards. They are made in advanced facilities that use cutting edge technology. Each part goes through thorough testing to confirm strength and safety, so you can trust it. FordPartsDeal.com gives you genuine Lincoln Tie Rod at some of the affordable online prices without cutting quality. Every OEM Lincoln part includes the manufacturer's warranty, easy returns, and super-fast delivery. So why wait? Shop now and get your vehicle back to peak condition.

Lincoln Tie Rod Parts and Q&A

Inner Tie Rod
2L1Z-3280-GA
Q: How to service and repair the Tie Rod on Lincoln Navigator?
A:
A substantial step before servicing or repairing the toe link is to deactivate the air suspension system by disabling the air suspension switch positioned in the LH rear quarter trim panel because skipping this procedure can trigger unexpected air spring inflation or deflation that produces vehicle movement. Start the procedure by taking off the wheel together with the tire component. The hex holding feature should be used before removing the nut so the stud stays stationary before the toe link needs to be removed from the wheel knuckle. The second step involves unstowing the toe link and the nut from the system. To install the system follow the opposite order of steps from removal and inspect and adjust the rear toe if required.
Inner Tie Rod
8W7Z-3280-A
Q: How to service and repair the inner tie rod on Lincoln Town Car?
A:
The servicing and repair of inner tie rod starts with wheel removal and tire detachment followed by loosening the tie-rod jam nut until you tighten it to 55 Nm (41 lb-ft) torque during reinstallation. A hex holding feature must be used to stop the stud from turning when taking out the nut and the outer tie-rod end should be detached from the wheel knuckle using a torque setting of 80 Nm (59 lb-ft). Write down the number of outer tie-rod end turns as they will be needed during reassembly before you remove this component. First disconnect the tie-rod jam nut then for those who need to fix the right-side inner tie rod it becomes essential to stretch the bellows boot on the left-side for steering gear control. Detach both clamps from the bellows boot while taking off the boot itself. The steering gear must be set at center position while using an appropriate crowfoot wrench to secure the rack gear flat area when installing the inner tie rod. Tighten this rod to 100 Nm (74 lb-ft) torque specifications after installation. The removal of abrasive material should be complete because it can cause damage to the steering gear while avoiding twists of the bellows boot for protection. The inner tie-rod groove should receive an application of grease before the bellows boot placement while ensuring appropriate positioning on the steering gear housing bead and inside the inner tie-rod channel. The procedure for removal inversion leads to part cleaning for reusable components before new part installation. Checking and readjusting the front toe completes the procedure.