Ford 1W7Z-6B288-AB
Camshaft Position Sensor

The Camshaft Position Sensor servicing process begins by removing the ground cable of the battery. At the left-hand side of the engine remove both the air cleaner inlet pipe and resonator. First disconnect the electrical connector of the camshaft position sensor (CMP) from both sides followed by removal of the bolt attaching the CMP sensor. Follow the installation process by tightening the new sensor to 10 Nm (89 lb-in) torque value before performing the opposite removal steps to finish the work.

Service on the Camshaft Position Sensor starts by disconnecting the battery ground cable then draining part of the cooling system. First detach the air cleaner assembly before placing the heater water tube in a suitable position. Remove the bolt from the wiring harness before taking the tube to put aside. The process starts with disconnecting the CMP sensor electrical connector followed by unscrewing the sensor and removing it. The installation process requires executing the opposite steps compared to removal steps.

The service of the Camshaft Position Sensor begins by disconnecting the battery ground cable. Start by draining part of the cooling system fluid then remove the air cleaner assembly. The heater water tube needs to be positioned to the side first before disconnecting the wiring harness and taking out the bolt so the tube can remain safe. First disconnect CMP sensor electrical connector before removing its screws along with the sensor itself. The installation procedure requires performing the reverse steps of removal.

Service on the Camshaft Position Sensor starts by disconnecting the battery ground cable then draining part of the cooling system. First detach the air cleaner assembly before placing the heater water tube in a suitable position. Remove the bolt from the wiring harness before taking the tube to put aside. The process starts with disconnecting the CMP sensor electrical connector followed by unscrewing the sensor and removing it. The installation process requires executing the opposite steps compared to removal steps.

The service of the Camshaft Position Sensor starts with disconnecting the battery ground cable. The first step should involve disconnecting the electrical connector from the Camshaft Position (CMP) sensor. Untighten the bolt securing the CMP sensor before removing the sensor from its position. Based on removal procedure, re-install the components backward.

The battery ground cable needs to be disconnected first before starting work on the Camshaft Position Sensor. First detach the CMP sensor electrical connection and afterward loosen the bolt holding the sensor in place before removing it. Rephrase the installation process as the opposite steps of removing the sensor.

Service of the camshaft position (CMP) sensor requires users to disconnect the battery ground cable followed by disconnecting the CMP sensor electrical connector. First detach the bolt which holds the CMP sensor before removing it from its place. The installation process requires following the reversed steps of removal completion.

The service of the Camshaft Position Sensor requires initially removing the battery ground cable and then draining part of the cooling system. After disconnecting the engine harness from the water tube users should remove the bolt to position the heater water outlet tube aside. Disassembly of the CMP sensor starts by disconnecting its electrical connector followed by removal of CMP sensor retaining screws. The installation process should follow the reverse actions of removal.

A proper camshaft position (CMP) sensor service procedure begins with disconnecting the battery ground cable. Start by removing both the air cleaner and air cleaner outlet pipe from the apparatus. The CMP sensor electrical connection should be detached followed by removal of the bolt which maintains the CMP sensor position in place. Check the O-ring seal for damage then perform a replacement if needed. Application of clean engine oil on the O-ring seal should happen before installation. The installation of the CMP sensor requires tightening it to 10 Nm (89 lb-in) torque before you proceed with the reverse order of removal steps to finish the installation.

The first step for servicing the camshaft position (CMP) sensor requires a vehicle in NEUTRAL position with hoisting support. Start engine control services only after switching the ignition switch OFF to protect against equipment damage. The CMP sensor sits on the driver side of the engine so the technician needs to disconnect its electrical connector. First unscrew the bolt holding the CMP sensor and after that remove the sensor equipment alongside the O-ring seals to discard. Secure the bolt to 13 Nm when installing the sensor (115 lb-in torque). Place the blue O-ring seal first near the flange then position the red O-ring seal near the metal tip while verifying a proper seating of both components. Before installing the new O-ring seals apply clean engine oil on their surfaces. Recovery of the system starts when you perform the removal procedure in reverse order.

The first step for servicing the camshaft position sensor CMP requires disconnecting its electrical connector. First remove the bolt which secures the CMP sensor then pull out the sensor from its position. Before installing the new sensor you should apply clean engine oil on the O-ring seal to prepare it for its position. During installation of the bolt users should tighten it to 10 Nm (89 lb-in) while following up with the reverse order of removal to finalize installation.

The service of Camshaft Position Sensor requires users to start by disconnecting the battery ground cable. The service of the Camshaft Position sensor starts by first disconnecting the connector then removing the bolts which secure the sensor. After installing the Camshaft Position Sensor one should perform the steps in reverse order during removal.

Service of the Camshaft Position Sensor begins by removing the battery ground cable. You should first disconnect the Camshaft Position (CMP) sensor by removing its securing bolts then disconnecting its connector. The sensor installation follows the reversed steps from removal.

The Camshaft Position Sensor repair process should start by disconnecting the battery ground cable. Detach the electrical connector linking to CMP sensor before sensor removal can proceed. The service completion requires first reversing the initial removal sequence.

Begin service of the camshaft position (CMP) sensor by removing the battery ground cable followed by removing the CMP sensor electrical connector. The first step is to remove the bolt while taking out the CMP sensor. After cleaning the CMP sensor installation area reverse your repair steps to achieve successful mounting.

Start Camshaft Position Sensor service by removing the indicated components in the same order shown on the illustration and table while keeping in mind that the drive belt is not included. When performing installation of this component follow the steps in reverse order to finish it.

Service of the Camshaft Position Sensor starts with disconnecting the ground cable from the battery. The service of Camshaft Position (CMP) sensor begins with removal of electrical connector followed by sensor removal. When installing the constituent parts follow the exact opposite steps of removal.

Professional services on the Camshaft Position Sensor should begin by disconnecting the ground cable from the battery. Before sensor service you need to disconnect the electrical connector followed by removing the sensor. The installation process will be complete by performing the opposite steps of removal.

Service of the left-hand camshaft position (CMP) sensor begins by taking off the air cleaner outlet pipe. After disconnecting the CMP sensor electrical connector you must remove the bolt which secures the sensor. Tighten the bolt at 10 Nm (89 lb-in) during new sensor installation while you should apply engine oil to the O-ring seal before putting it into position. Finish the installation by reversing all steps of removal.

Users must begin the Camshaft Position Sensor servicing operation by disconnecting the battery ground cable. The first step includes disconnecting the electrical connector of the Camshaft Position (CMP) sensor followed by removing the sensor. Fitting this device requires following the steps of removing it in reverse order until finished.

Disconnect the electrical connector of the CMP sensor.

Disconnect the battery ground cable.

Remove the bolt securing the CMP sensor and take out the sensor itself.

Complete the process by reversing the removal steps.

Remove the CMP bolt.

First, disconnect the battery ground cable.

For installation, reverse the removal procedure.

Remove the bolt securing the CMP sensor.

Disconnect the battery ground cable.

Disconnect the electrical connector from the Camshaft Position (CMP) sensor.

Remove the bolt securing the sensor.

Disconnect the electrical connector from the Camshaft Position (CMP) sensor.

Disconnect the CMP sensor electrical connector and remove the bolts securing the CMP sensor.

Disconnect the electrical connector of the CMP sensor.

Remove the bolt securing the CMP sensor and take out the sensor itself.

Remove the bolt securing the CMP sensor and discard the O-ring seal.

Disconnect the battery ground cable.

Disconnect the CMP sensor electrical connector on both sides and remove the bolt securing the CMP sensor.

When reinstalling the CMP sensor, tighten it to 3 Nm (27 lb-in).

Tighten the CMP sensor to 3 Nm (27 lb-in).

Reverse the removal procedure.

Disconnect the electrical connector of the CMP sensor.

Disconnect the connector and then remove the bolts securing the sensor.

Disconnect the connector and then remove the bolts securing the sensor.

Tighten the bolt to 10 Nm (89 lb-in).

Disconnect the electrical connector of the CMP sensor and remove the bolt securing the sensor.

Begin by removing the air cleaner inlet pipe and resonator from the left-hand side.

Disconnect the electrical connector from the CMP sensor.

Reverse the removal procedure.

Reverse the removal procedure.

6 Nm (53 lb-in).

Disconnect the battery ground cable.

Reverse the removal procedure to secure the new sensor in place.