Ford 6L1Z-17508-AARM
Wiper Motor

The service of the rear wiper motor begins with taking out the rear wiper pivot arm together with the rear window wiper motor grommet. Bring open the liftgate window then remove the wiper motor cover trim panel. First disconnect electrical components before you remove two motor nuts securing the rear window wiper unit and retighten these nuts to 6 Nm (53 lb-in) at reinstallation. The rear window wiper motor should be removed during the next step. The installation process requires regular reversal of the removal steps with the final step requiring the nuts to be fastened to 10 Nm (89 lb-in).

Service of the windshield wiper motor begins by removing the wiper mounting arm together with the pivot shaft. Disconenct the mounting arm and pivot shaft linkage through the output shaft of the wiper motor by taking out the bolt and applying Threadlock to it if you plan to use it again afterward which should be tightened to 17 Nm (13 lb-ft). The repair of the windshield wiper motor begins by removing three securing bolts followed by tightening these bolts to 15 Nm (11 lb-ft) during reinstallation. Toward finishing the process you should reverse the removal steps while handling the motor with caution to protect the inner permanent magnets.

Service of the windshield wiper motor requires first detachment of the wiper mounting arm and pivot shaft assembly. After disconnecting the wiper pivot arm linkage you must remove three bolts from the windshield motor while applying torque to 15 Nm (11 lb-ft) for the reinstallation steps. The installation process finishes with the opposite order of removal procedures.

Start the windshield wiper motor servicing by taking out both the wiper mounting arm and pivot shaft. Using a wrench on the upper windshield wiper motor nut allows you to lift the bottom section of the wiper arm and shaft assembly for removing the lower nuts while performing a 15 Nm (11 lb-ft) torque on these nuts when reinstalling. During the windshield wiper motor installation substitute the 15 Nm torques specified for the upper motor nut. After bolt removal from the windshield wiper motor crank the technician must tighten this bolt to 17 Nm (13 lb-ft) at reinstallation. Conclude the installation process through reverse execution of the removal steps.

Prior to servicing the wiper motor take care because the internal permanent magnets made of glass-like material require gentle handling and should never be struck. The wiper service starts with removing the mounting arm along with the pivot shaft followed by removing the bolt which disconnects the arm and shaft from the motor output shaft. Before using the original bolt all users should treat it with Threadlock and torque it to 17 Nm (13 lb-ft). Once you have accomplished the removal of the three windshield wiper motor bolts you should install them by applying 15 Nm (11 lb-ft) of torque. You should reverse the procedure for removal to conduct the actual installation.

The procedure to service the rear window wiper motor requires starting with the removal of the rear wiper pivot arm together with the liftgate interior trim panel. The service requires beginning by removing the electrical connector attached to the rear wiper motor followed by unfastening its three mounting screws. The new rear wiper motor should be positioned on the liftgate while securing it with three screws that need to be tightened to 11 Nm (8 lb-ft). First connect the electrical connector of the rear wiper motor before reinstalling both the liftgate interior trim panel and securing the rear wiper pivot arm.

The service of windshield wiper motor requires the first step to uninstall the windshield wiper mounting arm together with its attached pivot shaft assembly. The first service step involves extracting the windshield wiper motor through bolt removal of both the output shaft and the motor attachment bolts. Repeat the reversal of the uninstallation steps for reinstallation.

You should begin windshield wiper motor servicing by taking out the wiper mounting arm along with pivot shaft assembly. The service process requires the user to disconnect the wiper pivot arm linkage along with removing the three windshield motor bolts which must be retightened to 18 Nm (13 lb-ft) torque during the reassembly. The completion of the task happens when you carry out the removal steps in opposite order.

Begin by removing the cowl top vent panels.

First, remove the windshield wiper mounting arm and pivot shaft.

Test the liftgate and liftgate glass for normal operation.

Reverse the removal procedure.

Begin by removing the front wiper pivot arms.

To ensure proper installation of the windshield wiper mounting arm and pivot shaft.

Reverse the removal procedure.

No, the windshield wiper motor is not serviceable separately.

Remove the rear wiper pivot arm.

Open the liftgate, install the rear window wiper striker and wiper pivot arm mounting assembly nuts, tightening them to 6 Nm (53 lb-in), then close the liftgate, install the rear window wiper pivot shaft nut and handle, tightening to 18 Nm (13 lb-ft), and finally install the dust boot cover and the rear wiper pivot arm.

Reverse the steps taken during removal.

Take out the windshield wiper motor by removing the bolts.

Disconnect the windshield wiper linkage.

Unclip the wiring harness from the wiper arm and position it aside.

Ensure to tighten the bolts to 15 Nm (11 lb-ft).

Installation is completed by reversing the removal procedure.

Disconnect the electrical connector.

Disconnect the electrical connector.

Disconnect the electrical connector and then remove the bolt and the windshield wiper linkage.

Begin by removing the rear wiper pivot arm and the liftgate trim panel.

Take out the rear wiper motor by removing the three bolts securing it and disconnecting the electrical connector.

Disconnect the electrical connector, unclip the wiring harness from the wiper arm, and position it aside.

Disconnect the electrical connector and remove the three bolts securing the rear window wiper assembly.

Installation is completed by reversing the removal procedure.

Disconnect the electrical connector and remove the three bolts securing the rear window wiper assembly.

Take off the wiper mounting arm and pivot shaft assembly by removing the five bolts and disconnecting the electrical connector.

Begin by removing the bolt securing the motor.

Reverse the removal procedure.

Begin by removing the wiper mounting arm and pivot shaft.

Open the liftgate glass and remove the nuts along with the rear window striker and wiper pivot shaft assembly, tightening them to 6 Nm (53 lb-in) during reinstallation.

First, remove the mounting arm and pivot shaft.

Begin by removing the rear wiper pivot arm and the liftgate interior trim panel.

Take out the bolts holding the windshield wiper motor in place.

Disconnect its electrical connector and remove the bolts.

Reverse the removal procedure.

Take out the windshield wiper motor bolts.

Reverse the removal procedure.

Detaching the wiper motor linkage arm may prevent the wiper arms from parking correctly.

Remove the two rear window wiper motor nuts.

Disconnect the electrical connectors.

Remove the bolt securing the windshield wiper linkage.