How to Properly Service and Repair a Tail Pipe and Muffler on Ford Crown Victoria?

You should initiate muffler and tailpipe servicing by placing your vehicle in neutral on the hoist system. The lifting procedure must start by shutting off air suspension electrical power to avoid unexpected spring changes that may cause vehicle movement. The two nuts and clamp need removal before installation where tightening to 48 Nm (35 ft. lbs.) becomes necessary. Make use of a suitable exhaust cutting tool to disconnect the muffler from the tailpipe. Perform an evaluation of isolators for quality before you detach the isolators to eliminate the tailpipe. Perform the same steps for the muffler while inspecting the necessary isolator for possible replacement. New exhaust fasteners should replace old ones during installation then the fasteners should remain loose until all components join before final tightening. Use a systematic tightening method to specify these fasteners which will achieve uniform assembly of the flanges before concluding at 33 Nm (24 ft. lbs.). Using oil or grease-based lubricants represents a danger to iso t2 the isolators and their rubber components because these substances will degrade the rubber material and permit the isolators to break away from their exhaust hanger bracket position when the vehicle runs.

How to Service and Repair the Tail Pipe and Muffler on Ford Ranger?

The procedure for muffler and tailpipe servicing starts with putting the vehicle into neutral mode on a hoist. To service the 2.3L engine vehicles requires removal of both exhaust downpipe-to-muffler and tailpipe assembly bolts as well as two flagnuts and a gasket which should be discarded. Vehicles with 4.0L engines require removal of two right-hand side exhaust Y-pipe-to-muffler and tailpipe assembly bolts accompanied by two flagnuts and one gasket that should be discarded together with the flagnuts. The procedure continues with disconnection of three rubber isolators which enables the muffler and tailpipe assembly to be removed. Follow the installation procedure by avoiding oil or grease-based lubricants on the isolators because they cause rubber deterioration. All mating areas of the muffler and tailpipe assembly need cleaning before the components can be reinstalled into the vehicle while attaching the three rubber isolators. The installation of new exhaust downpipe-to-muffler and tailpipe assembly gasket must be followed by torquing two exhaust downpipe-to-muffler and tailpipe assembly bolts along with two new flagnuts to 40 Nm (30 lb-ft). Implement new gasket installation for the 4.0L engine on right-hand exhaust Y-pipe-to-muffler and tailpipe assembly before torquing two right-hand side exhaust Y-pipe-to-muffler and tailpipe assembly bolts and two new flagnuts to 40 Nm (30 lb-ft). Check the exhaust system isolators for zero load before executing an exhaust system alignment procedure.

OEM Ford Tail Pipe

Exhaust Tail Pipe

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

Part Type

Exhaust Tip
Other Tail Pipes

Select Part Type

241 Tail Pipes found

View related parts
Ford Exhaust Pipe Part Number: 8G1Z-5G274-A
$11.06 MSRP: $15.68
You Save: $4.62 (30%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Tail Pipe
- Replaced by: 7T4Z-9450-AA
Fits the following Ford Models:
- Taurus | 2008-2009 | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Tail Pipe Part Number: 8C2Z-5202-A
$316.72 MSRP: $441.79
You Save: $125.07 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Pipe; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Tip; Tail Pipe Extension; Extension Pipe
- Replaces: 4C2Z-5202-AA
Fits the following Ford Models:
- E-150 | 2005-2007 | Base, Base Level 2, Chateau, RV Prep, XL, XLT | 5.4L V8, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
- E-150 Club Wagon | 2005 | Chateau, XL, XLT | 8 Cyl 5.4 L GAS
- E-250 | 2005-2007 | Base, Base Level 2, Chateau, RV Prep, XL, XLT | 5.4L V8, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
- E-350 Club Wagon | 2005 | Chateau, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
- E-350 Super Duty | 2015-2019, 2005-2007 | Base, Chateau, XL, XLT | 10 Cyl 6.8 L CNG, 10 Cyl 6.8 L GAS, 10 Cyl 6.8 L LPG, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS, 8 Cyl 5.4 L LPG, 8 Cyl 6.2 L FLEX
- E-350/E-350 Super Duty | 2005-2007 | Base, Base Level 2, Chateau, RV Prep, XL, XLT | 5.4L V8, 6.8L V10
- E-450 Super Duty | 2005-2007 | Base, Base Level 2, Chateau, RV Prep, XL, XLT | 5.4L V8, 6.8L V10
View More
View related parts
Ford Front Pipe Part Number: 5C3Z-5246-B
$545.84 MSRP: $755.12
You Save: $209.28 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Pipe; Resonator; Muffler
- Position: Front
- Replaces: 5C3Z-5246-DA
Fits the following Ford Models:
- F-250 Super Duty | 2005-2007 | FX4, King Ranch, Lariat, XL, XLT | 5.4L V8, 6.8L V10, 8 Cyl 5.4 L GAS
- F-350 Super Duty | 2005-2007 | FX4, King Ranch, Lariat, XL, XLT | 5.4L V8, 6.8L V10, 8 Cyl 5.4 L GAS
- F-450 Super Duty | 2005-2007 | FX4, Lariat, XL, XLT | 6.8L V10
- F-550 Super Duty | 2005-2007 | FX4, Lariat, XL, XLT | 6.8L V10
View More
View related parts
Ford Exhaust Pipe Part Number: FL1Z-5201-B
$644.63 MSRP: $855.22
You Save: $210.59 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Resonator; Tail Pipe; Muffler; Resonator & Pipe
Fits the following Ford Models:
- Expedition | 2015-2017 | EL King Ranch, EL Limited, EL Platinum, EL SSV, EL XL, EL XLT, King Ranch, Limited, Platinum, SSV, XL, XLT | 6 Cyl 3.5 L GAS
View related parts
Ford Exhaust Pipe Part Number: 7S4Z-5G203-C
$766.01 MSRP: $1016.27
You Save: $250.26 (25%)
ADD TO CART
Product Specifications
- Other Name: Tube Assembly; Flex Pipe; Flex Tube; Front Pipe
- Replaces: 5S4Z-5G203-AA
Fits the following Ford Models:
- Focus | 2005-2011 | LX, S, SE, SE Wagon, SEL, Series 25, SES, ST, SVT 3 Door, SVT 5 Door, ZTS, ZTW, ZX3, ZX4, ZX5, ZXW | 2.0L L4, 4 Cyl 2.0 L GAS
View related parts
Ford Exhaust Pipe Part Number: DB5Z-5G203-A
$800.66 MSRP: $1062.24
You Save: $261.58 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube Assembly; Exhaust Crossover Pipe; Front Pipe
Fits the following Ford Models:
- Police Interceptor Utility | 2013-2019 | Base | 6 Cyl 3.7 L FLEX, 6 Cyl 3.7 L GAS
View related parts
Ford Front Pipe Part Number: 7H6Z-5G274-A
$942.98 MSRP: $1251.04
You Save: $308.06 (25%)
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Crossover Pipe; Exhaust Y Pipe; Exhaust Pipe
- Position: Front
- Replaces: 7H6Z-5G274-AB
Fits the following Ford Models:
- Fusion | 2010-2012, 2007 | Base, High Version - Car, Hybrid, Low Version - Car, Mid Version - Car, Sport | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Ford Muffler & Pipe, Rear Part Number: F2GZ-5230-C
$1091.25 MSRP: $1447.76
You Save: $356.51 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Muffler Assembly - Rear; Exhaust Muffler; Exhaust Pipe; Muffler
- Position: Rear
Fits the following Ford Models:
- Edge | 2015-2018 | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Tail Pipe Extension Part Number: HC3Z-5202-A
$111.52 MSRP: $145.37
You Save: $33.85 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Extension - Exhaust Pipe; Exhaust Tail Pipe Tip; Exhaust Tail Pipe; Exhaust System; Exhaust Tip; Tailpipe Extension; Exhaust Pipe; Tail Pipe
- Replaces: BC3Z-5202-A
Fits the following Ford Models:
- F-250 Super Duty | 2017-2025, 2011 | King Ranch, Lariat, Platinum, XL, XLT | 6.2L V8, 8 Cyl 6.2 L FLEX, 8 Cyl 7.3 L GAS
- F-350 Super Duty | 2017-2025, 2011 | King Ranch, Lariat, Platinum, XL, XLT | 6.2L V8, 8 Cyl 6.2 L FLEX, 8 Cyl 7.3 L GAS
- F-450 Super Duty | 2011 | Lariat, XL, XLT | 6.2L V8
- F-550 Super Duty | 2011 | Lariat, XL, XLT | 6.2L V8
View More
View related parts
Ford Front Pipe Part Number: 7C3Z-5246-A
$133.97 MSRP: $174.63
You Save: $40.66 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Intermediate Pipe, Front; Exhaust Pipe; Direct-Fit Exhaust; Exhaust System Kit
- Position: Front
- Replaces: 7C3Z-5246-AC
Fits the following Ford Models:
- F-250 Super Duty | 2008-2010 | Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 5.4L V8, 6.8L V10, 8 Cyl 5.4 L GAS
- F-350 Super Duty | 2008-2010 | Cabela's, FX4, Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 5.4L V8, 6.8L V10, 8 Cyl 5.4 L GAS
- F-450 Super Duty | 2008 | FX4, Lariat, XL, XLT | 5.4L V8, 6.8L V10
- F-550 Super Duty | 2008 | FX4, Lariat, XL, XLT | 5.4L V8, 6.8L V10
View More
View related parts
Ford Front Pipe Part Number: AE5Z-5G203-C
$136.26 MSRP: $177.61
You Save: $41.35 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube Assembly; Exhaust Intermediate Pipe; Exhaust Pipe
- Position: Front
- Replaces: AE5Z-5G203-A
Fits the following Ford Models:
- Fusion | 2010-2012 | Base, High Version - Car, Hybrid, Low Version - Car, Mid Version - Car, S, SE, SEL, Sport | 2.5L L4, 4 Cyl 2.5 L GAS
View related parts
Ford Front Pipe Part Number: AE5Z-5G203-B
$152.40 MSRP: $198.66
You Save: $46.26 (24%)
ADD TO CART
Product Specifications
- Other Name: Tube Assembly; Exhaust Pipe
- Position: Front
Fits the following Ford Models:
- Fusion | 2010-2012 | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Exhaust Pipe, Front Part Number: 9A4Z-5G274-C
$258.44 MSRP: $339.85
You Save: $81.41 (24%)
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Crossover Pipe, Front; Exhaust Y Pipe; Tail Pipe; Front Pipe
- Position: Front
- Replaces: 9A4Z-5G274-B
Fits the following Ford Models:
- Flex | 2009-2012 | Base, Executive, Limited, SE, SEL, Titanium | 3.5L V6, 6 Cyl 3.5 L GAS
- Taurus X | 2008-2009 | Base, Eddie Bauer, Limited, SEL | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Ford Exhaust Pipe Part Number: BC3Z-5201-A
$236.08 MSRP: $310.45
You Save: $74.37 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Muffler Assembly; Muffler; Front Muffler
Fits the following Ford Models:
- F-250 Super Duty | 2011-2016 | King Ranch, Lariat, Platinum, XL, XLT | 8 Cyl 6.2 L FLEX
- F-350 Super Duty | 2011-2016 | King Ranch, Lariat, Platinum, XL, XLT | 8 Cyl 6.2 L FLEX
View related parts
Ford Tail Pipe Part Number: JL1Z-5201-A
$297.37 MSRP: $391.04
You Save: $93.67 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Pipe; Muffler; Rear Muffler
Fits the following Ford Models:
- Expedition | 2018-2024 | King Ranch, Limited, Platinum, SSV, Timberline, XL, XL STX, XLT | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Exhaust Pipe Part Number: CT4Z-5G274-A
$324.61 MSRP: $426.87
You Save: $102.26 (24%)
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Intermediate Pipe; Front Pipe
Fits the following Ford Models:
- Edge | 2012-2014 | Limited, SE, SEL | 4 Cyl 2.0 L GAS
View related parts
Ford Muffler W/Tpipe, Rear Part Number: CV6Z-5A289-E
$326.88 MSRP: $429.85
You Save: $102.97 (24%)
ADD TO CART
Product Specifications
- Other Name: Muffler Assembly - Rear; Exhaust Muffler Assembly; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Muffler
- Position: Rear
Fits the following Ford Models:
- Escape | 2013-2019 | S, SE | 4 Cyl 2.5 L GAS
View related parts
Ford Exhaust Pipe Part Number: BT4Z-5G274-B
$337.10 MSRP: $443.28
You Save: $106.18 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Crossover Pipe; Exhaust Y Pipe; Front Pipe
- Replaces: BT4Z-5G274-A
Fits the following Ford Models:
- Edge | 2011-2014 | Base, Limited, Lincoln, Premium, SE, SEL, SEL Plus (Limited), Sport, ST | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Ford Tail Pipe Extension Part Number: 7L1Z-5K238-A
Product Specifications
- Other Name: Extension - Exhaust Pipe; Exhaust Tip; Tail Pipe; Extension Pipe; Exhaust Pipe
- Manufacturer Note: Chrome Finish
- Replaces: 7L1Z-5255-AA
Fits the following Ford Models:
- Expedition | 2007-2014 | Eddie Bauer, EL Eddie Bauer, EL King Ranch, EL Limited, EL XL, EL XLT, Funkmaster Flex Edition, King Ranch, Limited, XL, XLS, XLT | 5.4L V8, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
Ford Exhaust Pipe, Front Part Number: DA5Z-5G203-A
$676.91 MSRP: $898.06
You Save: $221.15 (25%)
Product Specifications
- Other Name: Tube Assembly; Exhaust Intermediate Pipe, Front; Exhaust Crossover Pipe; Front Pipe
- Position: Front
Fits the following Ford Models:
- Police Interceptor Sedan | 2013-2019 | Base | 6 Cyl 3.7 L FLEX, 6 Cyl 3.7 L GAS

| Page 1 of 13 |Next >

1-20 of 241 Results

Ford Tail Pipe

If you own Ford and want to keep it in top shape, choosing OEM Tail Pipe is a smart move. They are precisely engineered and follow strict factory standards. They are made in advanced facilities that use cutting edge technology. Each part goes through thorough testing to confirm strength and safety, so you can trust it. FordPartsDeal.com gives you genuine Ford Tail Pipe at some of the affordable online prices without cutting quality. Every OEM Ford part includes the manufacturer's warranty, easy returns, and super-fast delivery. So why wait? Shop now and get your vehicle back to peak condition.

Ford Tail Pipe directs fast and hot exhaust away in order to protect power and safety. Since 1903, when Ford invented the game-changing moving assembly line, through to 2013, when it introduced the EcoBoost engines, which squeeze turbo power out of small engines, guzzle fuel, and SYNC voice control that allows a driver to tap the screen with a finger and scroll through music and maps. Ford includes Co-Pilot360 auto-squeezer, lane-help bars, and blind-spot foresight to reduce crash risks to both beginner and expert drivers. Ford now has battery-powered trucks, such as the F-150 Lightning, demonstrating that zero-tailpipe cruising does not need to be dramatic, nor does it need to be unable to tow boats and carry plywood. Tail Pipe is positioned on the end of the exhaust and is made rugged to endure rust, rock impacts, and heat. Ford identifies every Tail Pipe by stamping of steel grades that are equal to long-life catalytic converters, thus maintaining a smooth flow and low back-pressure. Tail Pipe choices include straight or angled ends allowing motorists to choose delicate or aggressive appearances without interfering with the engine parts. Tail Pipe upgrades also assist the emissions gear to work at peak so that gases are turned back to ensure that sensors are clean and that readings are accurate.

Ford Tail Pipe Parts and Q&A

Inlet Pipe
4W7Z-5246-BA
Q: How to Properly Service and Repair a Tail Pipe and Muffler on Ford Crown Victoria?
A:
You should initiate muffler and tailpipe servicing by placing your vehicle in neutral on the hoist system. The lifting procedure must start by shutting off air suspension electrical power to avoid unexpected spring changes that may cause vehicle movement. The two nuts and clamp need removal before installation where tightening to 48 Nm (35 ft. lbs.) becomes necessary. Make use of a suitable exhaust cutting tool to disconnect the muffler from the tailpipe. Perform an evaluation of isolators for quality before you detach the isolators to eliminate the tailpipe. Perform the same steps for the muffler while inspecting the necessary isolator for possible replacement. New exhaust fasteners should replace old ones during installation then the fasteners should remain loose until all components join before final tightening. Use a systematic tightening method to specify these fasteners which will achieve uniform assembly of the flanges before concluding at 33 Nm (24 ft. lbs.). Using oil or grease-based lubricants represents a danger to iso t2 the isolators and their rubber components because these substances will degrade the rubber material and permit the isolators to break away from their exhaust hanger bracket position when the vehicle runs.
Extension
4L5Z-5K238-AA
Q: How to Service and Repair the Tail Pipe and Muffler on Ford Ranger?
A:
The procedure for muffler and tailpipe servicing starts with putting the vehicle into neutral mode on a hoist. To service the 2.3L engine vehicles requires removal of both exhaust downpipe-to-muffler and tailpipe assembly bolts as well as two flagnuts and a gasket which should be discarded. Vehicles with 4.0L engines require removal of two right-hand side exhaust Y-pipe-to-muffler and tailpipe assembly bolts accompanied by two flagnuts and one gasket that should be discarded together with the flagnuts. The procedure continues with disconnection of three rubber isolators which enables the muffler and tailpipe assembly to be removed. Follow the installation procedure by avoiding oil or grease-based lubricants on the isolators because they cause rubber deterioration. All mating areas of the muffler and tailpipe assembly need cleaning before the components can be reinstalled into the vehicle while attaching the three rubber isolators. The installation of new exhaust downpipe-to-muffler and tailpipe assembly gasket must be followed by torquing two exhaust downpipe-to-muffler and tailpipe assembly bolts along with two new flagnuts to 40 Nm (30 lb-ft). Implement new gasket installation for the 4.0L engine on right-hand exhaust Y-pipe-to-muffler and tailpipe assembly before torquing two right-hand side exhaust Y-pipe-to-muffler and tailpipe assembly bolts and two new flagnuts to 40 Nm (30 lb-ft). Check the exhaust system isolators for zero load before executing an exhaust system alignment procedure.