Should engine mounts be replaced immediately if they are broken or deteriorated in four cylinder engine on Mercury Capri?

Engine mounts are generally trouble-free, but any that are cracked or worn should be replaced to help avoid rash or the related part wear. To check the mounts, stand the engine up to take pressure off of it and the mounts for inspection. First, raise the car safely on jackstands and place a jack in such a manner under the engine oil pan and put a big wooden block in between the head of the jack and the oil pan then slowly lift the engine a little in order to take the pressure off the mounts. Check the mounts for any signs of cracking, rigidness of the rubber or where the rubber stops and the metal plates starts, as the rubber can split right down the middle. Some of the shake or bounce could be transferred between the mount plates and the engine or frame as the assembly is lowered; this should be assessed for any relative motion using a large screwdriver or pry bar; where motion is noted, the assembly should be dropped and the mount fasteners tightened in their usual manner. To prevent further aggravation of the situation, it is recommended to use rubber preservative at the mounts. As for replacement, remove the negative battery terminal, lift the car and set it on suitable jackstands if not already applied. Take off the fasteners to free the mount from the frame bracket and lift the engine up a little by the use of a jack or hoist, at this angle ensure that the fan does not bump into the radiator or shroud, take off the mount to block nuts or bolts. Toruing of the mount bolts as well as the application of thread locking compound is done during installation and it is done in a sequential manner that is in an opposing order to the removal process.

OEM Mercury Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

212 Engine Mounts found

View related parts
Mercury Transmission Mount, Rear Part Number: 5L8Z-6038-AA
$45.87 MSRP: $65.62
You Save: $19.75 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Support; Manual/Auto Trans Mount; Mount Torque Strut & Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Bracket Insulator
- Position: Rear
Fits the following Mercury Models:
- Mariner | 2007-2011 | Base, Luxury, Premier | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Support Bracket Part Number: 5M6Z-6031-AA
$30.75 MSRP: $42.54
You Save: $11.79 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Automatic Transmission Mount Bracket; Automatic Transmission Mount; Rear Support; Transmission Mount
Fits the following Mercury Models:
- Mariner | 2006-2011 | Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Side Mount, Rear Part Number: 9L8Z-6068-A
$85.90 MSRP: $125.03
You Save: $39.13 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount, Rear; Engine Mount Bracket; Motor Mount; Rear Mount; Mount
- Position: Rear
- Replaces: 5L8Z-6068-BB, 5L8Z-6068-BA
Fits the following Mercury Models:
- Mariner | 2005-2011 | Base, Luxury, Premier | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mount Bracket Part Number: 9E5Z-6061-C
$50.88 MSRP: $72.78
You Save: $21.90 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Support; Engine Mount Bracket; Motor Mount
Fits the following Mercury Models:
- Milan | 2010-2011 | Base, Premier | 4 Cyl 2.5 L GAS
View related parts
Mercury Transmission Mount, Upper Part Number: 9E5Z-6038-G
$78.98 MSRP: $121.55
You Save: $42.57 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount, Upper; Transfer Case Mount
- Position: Upper
Fits the following Mercury Models:
- Milan | 2010-2011 | Base, Premier | 4 Cyl 2.5 L GAS
View related parts
Mercury Motor Mount Part Number: 6L8Z-6068-AA
$96.94 MSRP: $141.10
You Save: $44.16 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount; Engine Mount Bracket; Side Mount; Front Mount; Rear Mount
- Replaces: 5L8Z-6068-AD
Fits the following Mercury Models:
- Mariner | 2005-2011 | Base, Luxury, Premier | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Front Mount Part Number: 9E5Z-6038-F
$68.91 MSRP: $100.30
You Save: $31.39 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount; Engine Mount Bracket; Motor Mount; Mount
- Replaces: 6E5Z-6038-CA, 6E5Z-6061-BA, 6E5Z-6038-CK
Fits the following Mercury Models:
- Milan | 2010-2011 | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Side Mount, Front Part Number: 6M6Z-6068-AB
$70.66 MSRP: $102.85
You Save: $32.19 (32%)
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount, Front; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Front Insulator
- Position: Front
- Replaces: 5M6Z-6068-AB
Fits the following Mercury Models:
- Mariner | 2006-2011 | Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Side Mount, Rear Part Number: 5L8Z-6068-AE
$71.36 MSRP: $103.87
You Save: $32.51 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount, Rear, Right; Engine Mount Bracket; Motor Mount; Rear Mount; Mount
- Position: Rear
- Replaces: 5L8Z-6068-AA
Fits the following Mercury Models:
- Mariner | 2005-2011 | Base, Luxury, Premier | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Motor Mount, Front Part Number: 6L8Z-6068-CA
$95.18 MSRP: $138.55
You Save: $43.37 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount Bracket; Front Engine Mount; Torque Strut.; Side Mount; Rear Mount; Front Insulator; Mount; Insulator
- Position: Front
- Replaces: 5L8Z-6068-CD
Fits the following Mercury Models:
- Mariner | 2005-2011 | Base, Convenience, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mercury Engine Support Part Number: 9L8Z-6P094-C
$99.25 MSRP: $144.47
You Save: $45.22 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Support - Engine Mounting - Front; Engine Mount Crossmember; Motor Mount
- Replaces: 9L8Z-6P094-B
Fits the following Mercury Models:
- Mariner | 2009-2011 | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Torque Strut, Lower Part Number: 9E5Z-6068-B
$42.63 MSRP: $62.05
You Save: $19.42 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut, Lower; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Strut
- Position: Lower
Fits the following Mercury Models:
- Milan | 2010-2011 | Base, Premier | 4 Cyl 2.5 L GAS
View related parts
Mercury Transmission Mount Part Number: 5L8Z-6038-BA
$44.74 MSRP: $65.12
You Save: $20.38 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Transmission Mounts; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Front Mount
Fits the following Mercury Models:
- Mariner | 2005-2011 | Base, Convenience, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mercury Front Mount, Driver Side Part Number: 9L8Z-6031-A
$24.26 MSRP: $33.01
You Save: $8.75 (27%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Engine Mount Bracket, Left; Motor Mount; Engine Mount Bracket
- Position: Driver Side
Fits the following Mercury Models:
- Mariner | 2009-2011 | Base, Premier | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Front Bracket Part Number: 8L8Z-6061-BA
$29.40 MSRP: $40.01
You Save: $10.61 (27%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Support; Engine Mount Bracket, Front; Transmission Mount; Motor Mount; Bracket; Engine Mount Bracket
- Position: Front
Fits the following Mercury Models:
- Mariner | 2008-2011 | Base, Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Transmission Mount Part Number: 5M6Z-6038-AA
$34.08 MSRP: $46.38
You Save: $12.30 (27%)
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount.; Insulator
Fits the following Mercury Models:
- Mariner | 2006-2011 | Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Front Mount, Driver Side Part Number: 9L8Z-6031-B
$28.93 MSRP: $39.37
You Save: $10.44 (27%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Engine Mount Bracket, Left; Motor Mount; Engine Mount Bracket
- Position: Driver Side
Fits the following Mercury Models:
- Mariner | 2009-2011 | Base, Premier | 4 Cyl 2.5 L GAS
View related parts
Mercury Transmission Mount Bracket Part Number: 9L8Z-6M007-A
$28.93 MSRP: $39.37
You Save: $10.44 (27%)
ADD TO CART
Product Specifications
- Other Name: Bracket; Automatic Transmission Mount Bracket; Manual Transmission Mount Bracket; Transfer Case Mount; Transmission Mount
Fits the following Mercury Models:
- Mariner | 2009-2011 | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Transmission Mount Part Number: BE5Z-6038-C
$115.65 MSRP: $168.33
You Save: $52.68 (32%)
Ships in 1-3 Business Days
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount; Transfer Case Mount
Fits the following Mercury Models:
- Milan | 2011 | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Front Mount Part Number: F8DZ-6038-BA
Product Specifications
- Other Name: Insulator Assembly; Engine Mount Bracket; Motor Mount; Front Bracket
Fits the following Mercury Models:
- Sable | 1993 | GS, LS | 6 Cyl 3.0 L GAS

| Page 1 of 11 |Next >

1-20 of 212 Results

Mercury Engine Mount

If you own Mercury and want to keep it in top shape, choosing OEM Engine Mount is a smart move. They are precisely engineered and follow strict factory standards. They are made in advanced facilities that use cutting edge technology. Each part goes through thorough testing to confirm strength and safety, so you can trust it. FordPartsDeal.com gives you genuine Mercury Engine Mount at some of the affordable online prices without cutting quality. Every OEM Mercury part includes the manufacturer's warranty, easy returns, and super-fast delivery. So why wait? Shop now and get your vehicle back to peak condition.

Mercury Engine Mount prevents vibration to ensure that each ride is firm and quiet. Since its establishment in 1938 under the name of the Roman messenger, Mercury has been juggling between modest economics and outright luxury and a blend of sharp lines and a smooth, comfortable ride. Throughout all showrooms, Mercury emphasized spacious cabins and softer interiors, which kept external noise out and allowed drivers to steer with confidence. Suspensions remained soft but in check, therefore Mercury owners could drive long highways without becoming weary or the rattles taking the fun out of it. Mercury had given a legacy of comfortable midsized cars that struck a balance between comfort and pocket even after production ceased in 2011. The Engine Mount is applied to fasten the powerplant and transaxle in position, preventing the shake before it slips into the steering wheel or seats. The Engine Mount is constructed using a fluid-filled core and encased in a tough rubber insulator to absorb the impact pulses and harden electronically as the revs increase to produce a smooth start but firm control at speed. Periodically check the Engine Mount since old rubber or leakages may result in the engine dropping, leading to clunking, misaligned shafts, and increased repair costs. A new Engine Mount maintains performance sharp and cabin noise to a minimum.

Mercury Engine Mount Parts and Q&A

Motor Mount, Driver Side
E7ZZ-6038-F
Q: Should engine mounts be replaced immediately if they are broken or deteriorated in four cylinder engine on Mercury Capri?
A:
Engine mounts are generally trouble-free, but any that are cracked or worn should be replaced to help avoid rash or the related part wear. To check the mounts, stand the engine up to take pressure off of it and the mounts for inspection. First, raise the car safely on jackstands and place a jack in such a manner under the engine oil pan and put a big wooden block in between the head of the jack and the oil pan then slowly lift the engine a little in order to take the pressure off the mounts. Check the mounts for any signs of cracking, rigidness of the rubber or where the rubber stops and the metal plates starts, as the rubber can split right down the middle. Some of the shake or bounce could be transferred between the mount plates and the engine or frame as the assembly is lowered; this should be assessed for any relative motion using a large screwdriver or pry bar; where motion is noted, the assembly should be dropped and the mount fasteners tightened in their usual manner. To prevent further aggravation of the situation, it is recommended to use rubber preservative at the mounts. As for replacement, remove the negative battery terminal, lift the car and set it on suitable jackstands if not already applied. Take off the fasteners to free the mount from the frame bracket and lift the engine up a little by the use of a jack or hoist, at this angle ensure that the fan does not bump into the radiator or shroud, take off the mount to block nuts or bolts. Toruing of the mount bolts as well as the application of thread locking compound is done during installation and it is done in a sequential manner that is in an opposing order to the removal process.