Other Name: Latch; Door Latch Assembly, Front Right; Door Lock; Door Latch Assembly
Position: Front Passenger Side
Replaces: 6L1Z-1621812-A
Fits the following Ford Models:
Expedition | 2007-2009 | Eddie Bauer, EL Eddie Bauer, EL King Ranch, EL Limited, EL XLT, Funkmaster Flex Edition, King Ranch, Limited, XLT | 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
Other Name: Latch; Door Latch Assembly, Front Left; Door Lock; Door Latch Assembly
Position: Front Driver Side
Replaces: 6L1Z-1621813-A
Fits the following Ford Models:
Expedition | 2007-2009 | Eddie Bauer, EL Eddie Bauer, EL King Ranch, EL Limited, EL XLT, Funkmaster Flex Edition, King Ranch, Limited, XLT | 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
Other Name: Latch; Door Latch Assembly, Front Left; Latch Assembly
Position: Front Driver Side
Replaced by: NL1Z-78219A65-F
Replaces: KL1Z-78219A65-D, KL1Z-78219A65-B
Fits the following Ford Models:
Expedition | 2018-2024 | King Ranch, Limited, Max King Ranch, Max Limited, Max Platinum, Max SSV, Max XL, Max XLT, Platinum, SSV, Timberline, XL, XL STX, XLT | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
Other Name: Latch; Door Latch Assembly, Rear Left; Latch Assembly
Position: Rear Driver Side
Replaces: KL1Z-7826413-B
Fits the following Ford Models:
Expedition | 2018-2024 | King Ranch, Limited, Max King Ranch, Max Limited, Max Platinum, Max SSV, Max XL, Max XLT, Platinum, SSV, Timberline, XL, XL STX, XLT | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
Other Name: Latch; Door Latch Assembly, Front Right; Latch Assembly
Position: Front Passenger Side
Replaces: KL1Z-78219A64-B, KL1Z-78219A64-D
Fits the following Ford Models:
Expedition | 2018-2024 | King Ranch, Limited, Max King Ranch, Max Limited, Max Platinum, Max SSV, Max XL, Max XLT, Platinum, SSV, Timberline, XL, XL STX, XLT | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
| Page 1 of 27 |Next >
1-20 of 535 Results
Ford Door Latch Assembly Parts Questions & Experts Answers
Q: How to remove and replace the rear Door Latch Assembly on Ford Explorer?
A: Begin by detaching the rear door trim panel along with positioning the watershield aside before starting the rear door latch removal and replacement process. The integration of the interior door handle actuating cable locator at the door frame requires the removal of its frame piece and opening the locking clip before disconnecting the exterior handle actuating rod. First disconnect the electrical wires of the rear door ajar switch and rear door lock actuator before removing the three rear door latch screws which should be tightened to 12 Nm (106 lb-in) during the installation process. The process of installing the rear door finish is complete by removing the door frame retainer rod of the push button and then reversing the initial removal steps.
Q: How to service and repair the front Door Latch Assembly on Ford Mustang?
A: A technician should begin the front door latch repair by taking out the door trim panel. The release of actuating rods begins with clip opening followed by screwdriver usage to free the lock cylinder actuating rod. You should first disconnect the door ajar switch along with actuator electrical connectors before removing screws that keep the door latch in place. The service and repair process starts by removing the water shield after which you should release the interior door handle actuating cable and end with unfastening the door latch. Installation of the unit will consist of performing the removal steps in reverse order.
Q: How to Remove and Replace the Front Door Latch Assembly on Ford Ranger?
A: Start by removing the front door trim panel then placing the watershield out of the way to access the front door latch. You should remove the bolt followed by the door glass channel before reinstalling it by tightening it to 12 Nm (106 lb-in). First disconnect the front door latch actuating rod of the door lock cylinder and unclip the exterior door handle actuating rod from its handle before removing the parts. Use the three front door latch screws to close the assembly while torquing them to 12 Nm (106 lb-in). The door ajar switch electrical connector and possibly the door lock actuator electrical connector need to be disconnected. The operator should positioned the door latch assembly to the side and remove the front door latch cable watershield before disconnecting the front door latch cable. Complete the front door latch removal by taking out the door latch push button rod and later removing the entire latch. Installation of the new latch requires performing the reverse procedure of removal.