How Can You Safely Service and Properly Install the Fuel Filler Hose on Ford Explorer?

Service the fuel tank filler pipe with utmost safety by staying away from fuel components both flames and smoking because the region contains volatile mixtures. The procedure for fuel tank repairs requires a cap or tape to cover all liquid and vapor fuel openings but they must be removed before final installation. To start the procedure use neutral mode and place a hoist beneath the vehicle. Take these steps for service on the fuel tank filler pipe by disconnecting the battery ground cable while opening the fuel tank filler cap. Reinstall the fuel tank filler cap bolts using 2 Nm (18 lb-in) torque then tighten each of the three bolts before completion. The two tabs situated on the fresh air vent tube in the fuel filler door pocket must be pressed down to detach it from the inner fenderwell. Commence by disconnecting the fuel pressure sensor vapor tube coupling to the fuel filler pipe vapor tube assembly and then proceed with taking off the rear axle vent hose and the dust separator hose. To remove the fuel tank filler pipe hose, loosen the clamp and disconnect the hose and reinstall it by tightening the clamp to 3 Nm (27 lb-in). Gently tighten the two mounting bolts of the fuel tank filler pipe assembly to 15 Nm (11 lb-ft) torque specifications during the installation process. Complete the installation process by performing the reverse actions of the removal procedure.

How to Service and Repair the Fuel Filler Hose on Ford Mustang?

The procedure for repairing or servicing the fuel tank filler pipe starts by taking out the fuel tank as the first step. Before proceeding with installation or service of the filler pipe you need to remove the bolts which secure both the filler pipe housing and the floor pan rubber boot attachment. First remove the hose attached to the upper section of the pipe before swinging the pipe down to clear the pocket in the filler pipe and extract the pipe into the trunk space. Reverse the steps for installation when servicing the fuel tank filler pipe.

What precautions should be taken when servicing the fuel filler hose to prevent fire hazards and personal injury on Ford Ranger?

Precautions must be taken when servicing the fuel filler hose because highly flammable mixtures in fuel-related components create a risk for personal injury. Therefore, you must avoid both smoking and carrying any lighted tobacco or open flames while near these components. Thousands of pounds of pressure sustain within the fuel system after shutting off the engine therefore system pressure relief must come first before you disconnect any fuel line or component to stop dangerous fuel spray that creates fire hazards. To prevent accidental fuel spraying you should first reduce system pressure then undo the fuel tank filler pipes by releasing their hose clamps and disconnecting the filler pipes from the hose tubes. Start removal of the fuel tank filler pipe through screw removal. Follow the reverse order of steps used for removal to conduct the installation.

OEM Ford Fuel Filler Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

163 Fuel Filler Hoses found

View related parts
Ford Filler Neck
Part Number: AE5Z-9034-AH
$141.06 MSRP: $205.33
You Save: $64.27 (32%)
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Fuel Filler Hose; Pipe Assembly; Filler Pipe
- Replaces: AE5Z-9034-AA, AE5Z-9034-X, AE5Z-9034-AE, AE5Z-9034-T
Fits the following Ford Models:
- Fusion | 2010-2012 | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Tank Pressure Sensor
Part Number: BV6Z-9C047-B
$107.81 MSRP: $181.00
You Save: $73.19 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube - Fuel Feed; Evaporative Emissions System Lines; PCV Valve Hose; EGR Tube; Tube
Fits the following Ford Models:
- Focus | 2012-2018 | SE, SEL, ST, Titanium | 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS
View related parts
Ford Tank Pressure Sensor
Part Number: BV6Z-9C047-A
$108.29 MSRP: $181.80
You Save: $73.51 (41%)
ADD TO CART
Product Specifications
- Other Name: Tube - Fuel Feed; Evaporative Emissions System Lines; PCV Valve Hose; EGR Tube; Tube
- Manufacturer Note: Part Includes 9C052 Pressure Transducer
Fits the following Ford Models:
- Focus | 2012-2018 | S, SE, SEL, ST, Titanium | 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS
View related parts
Ford Filler Neck
Part Number: GV6Z-9034-B
$303.32 MSRP: $445.40
You Save: $142.08 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Tank Filler Neck; Fuel Filler Hose; Filler Pipe
Fits the following Ford Models:
- Escape | 2017-2019 | SE, SEL, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS
View related parts
Ford Filler Neck
Part Number: AL5Z-9034-A
$256.51 MSRP: $376.67
You Save: $120.16 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Tank Filler Neck; Filler Neck Hose; Fuel Filler Hose; Fuel Filler Neck; Filler Pipe
- Replaces: F47Z-9034-P, F37Z-9034-E
Fits the following Ford Models:
- Ranger | 1993-1997 | Sport, STX, XL, XL Sport, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Filler Neck
Part Number: CL8Z-9034-B
$289.43 MSRP: $425.00
You Save: $135.57 (32%)
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Cap; Fuel Tank Filler Neck; Filler Neck Hose; Fuel Filler Hose; Filler Pipe
- Replaces: 9L8Z-9034-A, AL8Z-9034-D, AL8Z-9034-C, AL8Z-9034-B, AL8Z-9034-A, BL8Z-9034-A, CL8Z-9034-A
Fits the following Ford Models:
- Escape | 2009-2012 | Hybrid, Limited, Limited Hybrid, XLS, XLT | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Filler Neck
Part Number: BC3Z-9034-EJ
$253.11 MSRP: $371.67
You Save: $118.56 (32%)
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Fuel Filler Hose; Filler Pipe
- Replaces: BC3Z-9034-Z, BC3Z-9034-J
Fits the following Ford Models:
- F-250 Super Duty | 2011-2016 | King Ranch, Lariat, Platinum, XL, XLT | 8 Cyl 6.7 L DIESEL
- F-350 Super Duty | 2011-2016 | King Ranch, Lariat, Platinum, XL, XLT | 8 Cyl 6.7 L DIESEL
View related parts
Ford Tube Assembly
Part Number: CK4Z-9J280-B
$61.47 MSRP: $103.20
You Save: $41.73 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel; Fuel Return Line
- Replaces: CK4Z-9155-A, CK4Z-9155-F, FG-1151, FG-1153, FG-1138, CK4Z-9155-G
Fits the following Ford Models:
- Transit-150 | 2015-2019 | Base, XL, XLT | 5 Cyl 3.2 L DIESEL
- Transit-250 | 2015-2019 | Base, PTV | 5 Cyl 3.2 L DIESEL
- Transit-350 | 2015-2019 | Base, XL, XLT | 5 Cyl 3.2 L DIESEL
- Transit-350 HD | 2015-2019 | Base, XL, XLT | 5 Cyl 3.2 L DIESEL
View More
View related parts
Ford Filler Neck
Part Number: GV6Z-9B149-A
$260.94 MSRP: $489.15
You Save: $228.21 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Fuel System Conversion; Filler Pipe
- Replaces: GV6Z-9034-A
Fits the following Ford Models:
- Escape | 2017-2019 | S | 4 Cyl 2.5 L GAS
View related parts
Ford Filler Neck
Part Number: AA5Z-9034-F
$176.35 MSRP: $256.70
You Save: $80.35 (32%)
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Fuel Filler Hose; Filler Pipe
- Replaces: AA5Z-9034-E, AA5Z-9034-A, AA5Z-9034-B
Fits the following Ford Models:
- Taurus | 2010-2012 | Limited, SE, SEL, SHO | 6 Cyl 3.5 L GAS
View related parts
Ford Filler Neck
Part Number: CL3Z-9034-B
$175.07 MSRP: $254.83
You Save: $79.76 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Fuel Filler Hose; Filler Pipe
- Replaces: AL3Z-9034-F, AL3Z-9034-B, BL3Z-9034-A
Fits the following Ford Models:
- F-150 | 2010-2012 | Harley-Davidson Edition, Lariat, Lariat Limited, Platinum, SVT Raptor | 8 Cyl 5.4 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Ford Filler Hose, Lower
Part Number: FV6Z-9047-E
$67.31 MSRP: $103.58
You Save: $36.27 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose - Filler Pipe; Fuel Filler Neck, Lower; Fuel Filler Hose
- Position: Lower
- Replaces: FV6Z-9047-D, FV6Z-9047-C, FV6Z-9047-A
Fits the following Ford Models:
- C-Max | 2013-2018 | Energi SE, Energi SEL, Energi Titanium, Hybrid SE, Hybrid SEL, Hybrid Titanium | 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Filler Neck
Part Number: AL5Z-9034-B
$265.59 MSRP: $390.00
You Save: $124.41 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Tank Filler Neck; Filler Neck Hose; Fuel Filler Hose; Fuel Filler Neck; Filler Pipe
- Replaces: F37Z-9034-C, F47Z-9034-N
Fits the following Ford Models:
- Ranger | 1995-1997 | Splash, Sport, STX, XL, XL Sport, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Return Hose
Part Number: DV6Z-9C047-A
$109.48 MSRP: $183.80
You Save: $74.32 (41%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube - Fuel Feed; Evaporative Emissions System Lines
- Manufacturer Note: Part Includes 9C052 Pressure Transducer
Fits the following Ford Models:
- Transit Connect | 2014-2022 | Titanium, XL, XLT | 4 Cyl 1.6 L GAS, 4 Cyl 2.5 L CNG, 4 Cyl 2.5 L GAS, 4 Cyl 2.5 L LPG
View related parts
Ford Feed Line
Part Number: GJ7Z-9C047-A
$137.29 MSRP: $218.00
You Save: $80.71 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube - Fuel Feed; Fuel Hose; PCV Valve Hose; EGR Tube; Tube Assembly
- Manufacturer Note: Part Includes 9C052 Pressure Transducer
Fits the following Ford Models:
- Escape | 2017-2019 | SE, SEL, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Return Hose
Part Number: DG1Z-9C047-C
$197.26 MSRP: $316.00
You Save: $118.74 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube - Fuel Feed; Evaporative Emissions System Lines; Canister Hose
- Manufacturer Note: Part Includes 9C052 Pressure Transducer
Fits the following Ford Models:
- Police Interceptor Sedan | 2013-2019 | Base | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L FLEX, 6 Cyl 3.7 L GAS
- Taurus | 2013-2019 | Limited, SE, SEL, SHO | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Return Hose
Part Number: DG1Z-9C047-B
$197.26 MSRP: $316.00
You Save: $118.74 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube - Fuel Feed; Evaporative Emissions System Lines; Canister Hose
- Manufacturer Note: Part Includes 9C052 Pressure Transducer
Fits the following Ford Models:
- Police Interceptor Sedan | 2013-2019 | Base | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
- Special Service Police Sedan | 2014-2018 | Base | 4 Cyl 2.0 L GAS
- Taurus | 2013-2019 | Limited, SE, SEL | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View More
View related parts
Ford Tube
Part Number: 9T1Z-9C047-A
$79.89 MSRP: $120.55
You Save: $40.66 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube - Fuel Feed; Evaporative Emissions System Lines; PCV Valve Hose; EGR Tube
Fits the following Ford Models:
- Transit Connect | 2010-2013 | XL, XLT, XLT Premium | 4 Cyl 2.0 L GAS
View related parts
Ford Filler Neck
Part Number: ML3Z-9034-C
$421.99 MSRP: $619.67
You Save: $197.68 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Fuel Filler Hose; Filler Pipe
Fits the following Ford Models:
- F-150 | 2021 | King Ranch, Lariat, Platinum, XL, XLT | 6 Cyl 3.0 L DIESEL
View related parts
Ford Filler Neck
Part Number: NZ6Z-9034-A
$282.16 MSRP: $414.33
You Save: $132.17 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Fuel Filler; Fuel Filler Neck; Fuel Tank Filler Neck; Fuel Filler Hose; Filler Pipe
- Replaced by: NZ6Z-9034-D
Fits the following Ford Models:
- Maverick | 2022-2023 | Lariat, XL, XLT | 4 Cyl 2.0 L GAS

| Page 1 of 9 |Next >

1-20 of 163 Results

Ford Fuel Filler Hose Parts Questions & Experts Answers

Filler Hose
4L2Z-9047-AA
Q: How Can You Safely Service and Properly Install the Fuel Filler Hose on Ford Explorer?
A: Service the fuel tank filler pipe with utmost safety by staying away from fuel components both flames and smoking because the region contains volatile mixtures. The procedure for fuel tank repairs requires a cap or tape to cover all liquid and vapor fuel openings but they must be removed before final installation. To start the procedure use neutral mode and place a hoist beneath the vehicle. Take these steps for service on the fuel tank filler pipe by disconnecting the battery ground cable while opening the fuel tank filler cap. Reinstall the fuel tank filler cap bolts using 2 Nm (18 lb-in) torque then tighten each of the three bolts before completion. The two tabs situated on the fresh air vent tube in the fuel filler door pocket must be pressed down to detach it from the inner fenderwell. Commence by disconnecting the fuel pressure sensor vapor tube coupling to the fuel filler pipe vapor tube assembly and then proceed with taking off the rear axle vent hose and the dust separator hose. To remove the fuel tank filler pipe hose, loosen the clamp and disconnect the hose and reinstall it by tightening the clamp to 3 Nm (27 lb-in). Gently tighten the two mounting bolts of the fuel tank filler pipe assembly to 15 Nm (11 lb-ft) torque specifications during the installation process. Complete the installation process by performing the reverse actions of the removal procedure.
Filler Neck
3R3Z-9034-AA
Q: How to Service and Repair the Fuel Filler Hose on Ford Mustang?
A: The procedure for repairing or servicing the fuel tank filler pipe starts by taking out the fuel tank as the first step. Before proceeding with installation or service of the filler pipe you need to remove the bolts which secure both the filler pipe housing and the floor pan rubber boot attachment. First remove the hose attached to the upper section of the pipe before swinging the pipe down to clear the pocket in the filler pipe and extract the pipe into the trunk space. Reverse the steps for installation when servicing the fuel tank filler pipe.
Filler Neck
XL5Z-9034-DB
Q: What precautions should be taken when servicing the fuel filler hose to prevent fire hazards and personal injury on Ford Ranger?
A: Precautions must be taken when servicing the fuel filler hose because highly flammable mixtures in fuel-related components create a risk for personal injury. Therefore, you must avoid both smoking and carrying any lighted tobacco or open flames while near these components. Thousands of pounds of pressure sustain within the fuel system after shutting off the engine therefore system pressure relief must come first before you disconnect any fuel line or component to stop dangerous fuel spray that creates fire hazards. To prevent accidental fuel spraying you should first reduce system pressure then undo the fuel tank filler pipes by releasing their hose clamps and disconnecting the filler pipes from the hose tubes. Start removal of the fuel tank filler pipe through screw removal. Follow the reverse order of steps used for removal to conduct the installation.