How to service and repair the automatic transmission shifter on Mercury Mariner?

The first step for automatic transmission shifter maintenance requires putting the selector lever in position (D). You should first gently lift the upper selector lever trim ring then raise the center console lid before you pull out the center console compartment tray. Start by removing the top finish panel while you detach the selector lever cable from the assembly through bracket removal of its cable end. Detach wiring harness retainers together with electrical connectors at the selector lever area where you should separate both the selector lever electrical connector and the vehicle harness connector. The AWD module of all-wheel drive vehicles needs pulling backward to detach from the selector lever back. Next invoke a centered console center console screw extraction to start the selector lever assembly extraction process followed by removal of the four bolts securing the assembly base. To put it into place install the selector lever assembly while securing it with the four bolts tightened to 15 Nm (11 lb-ft) before you add the two center console screws. The back of the selector lever requires AWD vehicles to attach their AWD module. Secure both electrical connectors to their designated location on the selector lever after ensuring correct installation of vehicle harness connector and mechanical selector electrical connector. Put back the wiring harness retainers and connect the selector lever cable to the selector lever assembly where it can be fastened to the bracket while being attached to its cable end. Reinstall the shift cable after readjusting it followed by the top finish panel together with the center console compartment tray and the upper selector lever trim ring.

How to Service and Repair the Column Automatic Transmission Shifter on Mercury Grand Marquis?

Start column shifter servicing and repair processes by ensuring immediate safety through back up power supply deplenishment to negate air bag deployment risks then disconnecting the battery ground cable followed by a one-minute wait and additional battery supply and power disconnect procedures when available. The service and repair of the column shift begins with unfastening the lower steering column opening finish panel screw while relocating the parking brake release handle. After that, remove the panel screw and pull outward to free its retaining clips. The repair process starts by removing the five screws from the lower steering column opening finish panel reinforcement and following this with the instrument panel reinforcement brace's four screws removal. You should disconnect and loosen the selector lever indicator cable by taking off its screw. After rotating the ignition switch lock cylinder to RUN position you can remove it by pressing the lock cylinder release pin followed by pulling it out. Four screws must be taken out from the steering column shroud before the steering column can be lowered by removing its four nuts. When performing the replacement start by taking off the upper steering column shroud and breaking the transmission control switch (TCS) harness connector free. The TCS harness needs to be disconnected from its locators while the gearshift lever cover needs to be divided from the steering column. Conducting a proper disposal of the old gearshift lever pin while removing the gearshift lever remains essential to the process. The completion of the installation requires following the steps in reverse order of removal.

OEM Mercury Automatic Transmission Shifter

AT Shifter

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

52 Automatic Transmission Shifters found

View related parts
Mercury Shift Lever Part Number: 7L2Z-7210-DB
$328.36 MSRP: $482.17
You Save: $153.81 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shifter Assembly; Gear Shift Assembly
- Replaces: 6L2Z-7210-WA, 7L2Z-7210-DA, 7L2Z-7210-D
Fits the following Mercury Models:
- Mountaineer | 2006-2010 | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Shifter Assembly Part Number: BL8Z-7210-CA
$99.23 MSRP: $135.03
You Save: $35.80 (27%)
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Automatic Transmission Selector Handle; Shift Lever; Gear Shift Assembly
Fits the following Mercury Models:
- Mariner | 2011 | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Gear Shift Assembly Part Number: CE5Z-7210-KA
$510.64 MSRP: $749.83
You Save: $239.19 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Automatic Transmission Selector Handle; Shift Housing
- Manufacturer Note: With +/- Button
- Replaces: BE5Z-7210-KA
Fits the following Mercury Models:
- Milan | 2011 | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Shift Lever Part Number: 5F1Z-7210-D
$7.13 MSRP: $9.87
You Save: $2.74 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing Assembly - Gear Shift
Fits the following Mercury Models:
- Sable | 2000-2002 | GS, LS, LS Premium | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Shift Lever Part Number: 7L5Z-7210-AA
$108.19 MSRP: $157.48
You Save: $49.29 (32%)
Product Specifications
- Other Name: Lever - Transmission Gear Shift; Automatic/Manual Control Lever.; Gear Shift Assembly
- Replaces: 4L2Z-7210-BAA
Fits the following Mercury Models:
- Mountaineer | 2000-2001 | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Gear Shift Assembly Part Number: 5L8Z-7210-EA
$77.52 MSRP: $112.83
You Save: $35.31 (32%)
Product Specifications
- Other Name: Housing Assembly - Gear Shift
Fits the following Mercury Models:
- Mariner | 2005-2007 | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Shift Lever, Black/Charcoal Part Number: 8W1Z-7210-AC
Product Specifications
- Other Name: Lever; Automatic Transmission Shift Lever; Gear Shift Assembly
- Replaces: 5W1Z-7210-AAK
Fits the following Mercury Models:
- Grand Marquis | 2006-2011 | GS, LS | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Shift Lever Part Number: 5L2Z-7210-AA
Product Specifications
- Other Name: Lever - Transmission Gear Shift; Automatic Transmission Shift Lever; Gear Shift Assembly
- Replaces: 1L2Z-7210-AD
Fits the following Mercury Models:
- Mountaineer | 2002-2005 | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Shifter Assembly Part Number: 8L8Z-7210-B
Product Specifications
- Other Name: Lever - Gear Shift; Shift Lever
- Manufacturer Note: Chrome
Fits the following Mercury Models:
- Mariner | 2008 | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Shift Lever, Camel Part Number: 8W1Z-7210-AB
Product Specifications
- Other Name: Lever; Automatic Transmission Shift Lever; Gear Shift Assembly
- Replaces: 5W1Z-7210-AAJ
Fits the following Mercury Models:
- Grand Marquis | 2006-2011 | GS, LS | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Gear Shift Assembly Part Number: CE5Z-7210-GA
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Automatic Transmission Selector Handle; Shift Housing
- Manufacturer Note: With +/- Button
- Replaces: BE5Z-7210-GA
Fits the following Mercury Models:
- Milan | 2011 | Base, Premier | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Mercury Shift Lever Part Number: XW7Z-7210-AA
Product Specifications
- Other Name: Lever - Transmission; Gear Shift Assembly; Lever - Transmission Gear Shift
- Replaces: F8AZ-7210-BA
Fits the following Mercury Models:
- Grand Marquis | 1998-2002 | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Shift Lever, Graystone Part Number: 8W1Z-7210-AA
Product Specifications
- Other Name: Lever; Automatic Transmission Shift Lever; Gear Shift Assembly
- Replaces: 5W1Z-7210-AAL
Fits the following Mercury Models:
- Grand Marquis | 2006-2011 | GS, LS | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Shifter Part Number: 6M6Z-7210-A
Product Specifications
- Other Name: Lever - Gear Shift; Shift Lever
Fits the following Mercury Models:
- Mariner | 2006-2007 | Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Mercury Shifter Assembly Part Number: 6G1Z-7210-F
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shift Lever
- Manufacturer Note: Complete Assembly
- Replaces: 5G1Z-7210-CA, 5G1Z-7210-L, 5G1Z-7210-H, 6G1Z-7210-CA
Fits the following Mercury Models:
- Montego | 2005-2007 | Luxury, Premier | 6 Cyl 3.0 L GAS
View related parts
Mercury Gear Shift Assembly Part Number: F7CZ-7210-AH
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Selector Handle
- Manufacturer Note: #F6C6 7200-AJ
- Replaced by: F8CZ-7210-AA
Fits the following Mercury Models:
- Tracer | 1997 | GS, LS, Trio | 4 Cyl 2.0 L GAS
View related parts
Mercury Shift Lever Part Number: 3F1Z-7210-AA
Product Specifications
- Other Name: Lever - Gear Shift
- Manufacturer Note: Complete shifter assembly with shifter mechanism, bezel, and Woodgrained knob , Floor shift , with interior accent trim package "C"
Fits the following Mercury Models:
- Sable | 2003-2005 | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Shift Lever Part Number: 3F2Z-7210-AA
Product Specifications
- Other Name: Lever - Transmission Gear Shift; Manual Transmission Shift Lever; Automatic Transmission Selector Handle; Gear Shift Assembly
- Manufacturer Note: Includes knob and wiring
Fits the following Mercury Models:
- Monterey | 2004-2007 | Base, Convenience, Luxury, Premier | 6 Cyl 4.2 L GAS
View related parts
Mercury Gear Shift Assembly Part Number: 4M8Z-7210-A
Product Specifications
- Other Name: Lever - Gear Shift
- Replaced by: 7M8Z-7210-A
Fits the following Mercury Models:
- Milan | 2006 | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Shifter Assembly Part Number: 5G1Z-7210-K
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shift Lever
- Replaces: 5G1Z-7210-G
Fits the following Mercury Models:
- Montego | 2005 | Luxury, Premier | 6 Cyl 3.0 L GAS

| Page 1 of 3 |Next >

1-20 of 52 Results

Mercury Automatic Transmission Shifter

If you own Mercury and want to keep it in top shape, choosing OEM Automatic Transmission Shifter is a smart move. They are precisely engineered and follow strict factory standards. They are made in advanced facilities that use cutting edge technology. Each part goes through thorough testing to confirm strength and safety, so you can trust it. FordPartsDeal.com gives you genuine Mercury Automatic Transmission Shifter at some of the affordable online prices without cutting quality. Every OEM Mercury part includes the manufacturer's warranty, easy returns, and super-fast delivery. So why wait? Shop now and get your vehicle back to peak condition.

Mercury Automatic Transmission Shifter allows drivers to slide up and down between gears, enhancing control as well as ordinary road confidence. Mercury started with a promise of midsize comfort, combining a plush ride with sharp lines and a mythically borrowed name. Pilots appreciated the quietness of the interior, as Mercury would tune suspensions, padded cabins, and have the least amount of road talk without jacking fares. Mercury continued to roll out smooth steering yet honest value roomy Cougars and solid Grand Marquis sedans over decades. Showrooms had their own style and provided a wide range of color choices, broad bench seats, and dashboards that could be seen at a glance. The badge was a symbol of cars that could safely be relied on by ordinary families on long hauls along the highway but still arrive in style at dinner in town. Although the ride was discontinued in 2011, it is the ride quality and low-profile swagger that are still commended by loyal owners. The recent Mercury Automatic Transmission Shifter in the drivetrain represents a break with bulkier linkages by utilizing shift-by-wire electronics to recall park, reverse, neutral, and drive with fingertip taps, trimming weight, and refining response in all generations of the Grand Marquis. Since the Automatic Transmission Shifter makes every ratio shift smooth, the engine torque is not shaken by the jolts that shake the inferior systems. The Automatic Transmission Shifter is located inside the tunnel or on the column where drivers will be in easy reach hence they do not lose concentration on the road ahead. Smooth internals extend the life of the Automatic Transmission Shifter so that high mileage does not dampen the ride on a commute or a journey across the country.

Mercury Automatic Transmission Shifter Parts and Q&A

Shifter Assembly
8L8Z-7210-A
Q: How to service and repair the automatic transmission shifter on Mercury Mariner?
A:
The first step for automatic transmission shifter maintenance requires putting the selector lever in position (D). You should first gently lift the upper selector lever trim ring then raise the center console lid before you pull out the center console compartment tray. Start by removing the top finish panel while you detach the selector lever cable from the assembly through bracket removal of its cable end. Detach wiring harness retainers together with electrical connectors at the selector lever area where you should separate both the selector lever electrical connector and the vehicle harness connector. The AWD module of all-wheel drive vehicles needs pulling backward to detach from the selector lever back. Next invoke a centered console center console screw extraction to start the selector lever assembly extraction process followed by removal of the four bolts securing the assembly base. To put it into place install the selector lever assembly while securing it with the four bolts tightened to 15 Nm (11 lb-ft) before you add the two center console screws. The back of the selector lever requires AWD vehicles to attach their AWD module. Secure both electrical connectors to their designated location on the selector lever after ensuring correct installation of vehicle harness connector and mechanical selector electrical connector. Put back the wiring harness retainers and connect the selector lever cable to the selector lever assembly where it can be fastened to the bracket while being attached to its cable end. Reinstall the shift cable after readjusting it followed by the top finish panel together with the center console compartment tray and the upper selector lever trim ring.
Shift Lever
XW7Z-7210-AA
Q: How to Service and Repair the Column Automatic Transmission Shifter on Mercury Grand Marquis?
A:
Start column shifter servicing and repair processes by ensuring immediate safety through back up power supply deplenishment to negate air bag deployment risks then disconnecting the battery ground cable followed by a one-minute wait and additional battery supply and power disconnect procedures when available. The service and repair of the column shift begins with unfastening the lower steering column opening finish panel screw while relocating the parking brake release handle. After that, remove the panel screw and pull outward to free its retaining clips. The repair process starts by removing the five screws from the lower steering column opening finish panel reinforcement and following this with the instrument panel reinforcement brace's four screws removal. You should disconnect and loosen the selector lever indicator cable by taking off its screw. After rotating the ignition switch lock cylinder to RUN position you can remove it by pressing the lock cylinder release pin followed by pulling it out. Four screws must be taken out from the steering column shroud before the steering column can be lowered by removing its four nuts. When performing the replacement start by taking off the upper steering column shroud and breaking the transmission control switch (TCS) harness connector free. The TCS harness needs to be disconnected from its locators while the gearshift lever cover needs to be divided from the steering column. Conducting a proper disposal of the old gearshift lever pin while removing the gearshift lever remains essential to the process. The completion of the installation requires following the steps in reverse order of removal.