How to service and repair the front bumper cover on Ford Explorer?

Service and repair of the front bumper cover starts with disconnecting fog lamp electrical connectors when present and continuing with side lamp and front turn signal electrical connectors. The front fender inner splash shields can be accessed by removing screws and pin-type retainers followed by taking out the splash shields. You should now remove the screws located at the upper part of the bumper cover. The bottom of the front bumper cover requires rotation upward while gentle force against the top will release its four retaining tabs. The installation ends by performing the exact reverse procedure which occurred during removal.

How to service the front bumper cover on Ford Mustang?

Start the front bumper cover service with two part pin-type retainer removal along with the removal of the radiator upper sight shield (8C288). The first step is to remove two part pin-type retainers before proceeding with the front bumper cover nuts followed by the lower bumper cover pin-type retainers. After disconnecting the two parking lamps and two headlamps, remove the mounting clips (13N129). Proceed to remove the two part pin-type retainers and the headlamps (13007) from continuation. To detach the front bumper cover (17D957) raise up the tabs at the end of the process. Installation should follow the steps in reverse order to reinstall the components.

How can you repair a damaged rear bumper cover on Ford Ranger?

The inspection process enables you to determine whether repairs on a damaged rear bumper cover are justified by its ability to reach an acceptable state of quality while comparing the expenses to those of a new bumper replacement. The affected bumper needs removal so technicians can cleanse the broken tab(s) by using a plastics wax and grease remover. The repair area must receive hand sanding with 80-grit paper followed by compressed air usage for debris removal. please use plastics adhesion promoter in accordance with the product label instructions. Obtain a piece of fiberglass cloth or equivalent material that will completely cover the tab's front portion and extend in a sloped 51 mm (2 in) wedge starting from the original tab position. Before adding the affected area apply the pre-prepared repair adhesive cloth patch by placing the plastic repair material patch to create the tab shape right away. A small angle sander should be used after the appropriate cure time to shape the repair tab. The sander operation must stop before the exterior surface is reached. To finish the procedure you must repair paint damage on the bumper cover while utilizing Ford-approved paint systems before reinstalling the bumper cover system.

OEM Ford Bumper

Bumper Fascia

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

874 Bumpers found

View related parts
Ford Bumper Cover, Front
Part Number: 5L8Z-17D957-BAA
$171.75 MSRP: $265.05
You Save: $93.30 (36%)
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Front
- Position: Front
Fits the following Ford Models:
- Escape | 2005-2007 | Hybrid, XLT, XLT No Boundaries, XLT Sport | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Impact Bar, Front
Part Number: FR3Z-17757-C
$557.20 MSRP: $884.45
You Save: $327.25 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Impact Bar, Front
- Position: Front
Fits the following Ford Models:
- Mustang | 2015-2020 | Shelby GT350, Shelby GT350R | 8 Cyl 5.2 L GAS
View related parts
Ford Bumper Cover, Front
Part Number: HS7Z-17D957-BBPTM
$737.53 MSRP: $1170.68
You Save: $433.15 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front
- Position: Front
- Replaces: HS7Z-17D957-BAPTM
Fits the following Ford Models:
- Fusion | 2017-2018 | Energi Platinum, Energi SE, Energi Titanium, Platinum, Platinum Hybrid, S, S Hybrid, SE, SE Hybrid, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS
View related parts
Ford Bumper Cover, Front
Part Number: ES7Z-17757-DAPTM
$370.50 MSRP: $580.90
You Save: $210.40 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front
- Manufacturer Note: Paint to match
- Position: Front
- Replaces: DS7Z-17757-DAPTM
Fits the following Ford Models:
- Fusion | 2013-2016 | Energi SE, Energi Titanium, S, S Hybrid, SE, SE Hybrid, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L GAS
View related parts
Ford Lower Cover, Front
Part Number: FL1Z-17D957-AA
$205.11 MSRP: $319.48
You Save: $114.37 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front
- Manufacturer Note: BLACK
- Position: Front
Fits the following Ford Models:
- Expedition | 2016-2017 | EL SSV, SSV | 6 Cyl 3.5 L GAS
View related parts
Ford Lower Cover, Front
Part Number: BT4Z-17D957-CPTM
$307.07 MSRP: $478.30
You Save: $171.23 (36%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front Lower
- Manufacturer Note: Paint to match
- Position: Front Lower
Fits the following Ford Models:
- Edge | 2011-2014 | Sport | 6 Cyl 3.7 L GAS
View related parts
Ford Bumper, Front
Part Number: LC3Z-17757-D
$773.26 MSRP: $1145.57
You Save: $372.31 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Face Bar, Front
- Position: Front
Fits the following Ford Models:
- F-350 Super Duty | 2020-2022 | King Ranch, Lariat, Limited, Platinum, XL, XLT | 8 Cyl 6.2 L FLEX, 8 Cyl 6.7 L DIESEL, 8 Cyl 7.3 L GAS
View related parts
Ford Lower Cover, Rear
Part Number: FT4Z-17K835-H
$176.67 MSRP: $272.63
You Save: $95.96 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear Lower
- Position: Rear Lower
- Replaces: FT4Z-17K835-HPTM
Fits the following Ford Models:
- Edge | 2015-2018 | SE | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Lower Cover, Rear
Part Number: FT4Z-17K835-D
$157.52 MSRP: $243.08
You Save: $85.56 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear Lower
- Position: Rear Lower
- Replaces: FT4Z-17K835-DPTM
Fits the following Ford Models:
- Edge | 2015-2018 | SEL, Titanium | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Bumper Cover, Rear
Part Number: 4F1Z-17K835-CA
$182.82 MSRP: $282.13
You Save: $99.31 (36%)
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
Fits the following Ford Models:
- Taurus | 2004-2007 | LX, SE, SEL, SES | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Bumper Cover, Front
Part Number: HS7Z-17D957-CBPTM
$416.40 MSRP: $652.87
You Save: $236.47 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front
- Position: Front
- Replaces: HS7Z-17D957-CAPTM
Fits the following Ford Models:
- Fusion | 2017-2018 | Energi Platinum, Energi SE, Energi Titanium, Platinum, Platinum Hybrid, S, S Hybrid, SE, SE Hybrid, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS
View related parts
Ford Bumper, Rear
Part Number: ML3Z-17906-KAPTM
$521.79 MSRP: $766.22
You Save: $244.43 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Rear
- Position: Rear
- Replaces: PL3Z-17810-AAPTM
Fits the following Ford Models:
- F-150 | 2021-2023 | Tremor, XL, XLT | 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.3 L FLEX, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS, 8 Cyl 5.0 L FLEX
View related parts
Ford Bumper Cover, Rear
Part Number: GJ5Z-17K835-EA
$266.15 MSRP: $414.57
You Save: $148.42 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
Fits the following Ford Models:
- Escape | 2017-2019 | SE, SEL, Titanium | 4 Cyl 1.5 L GAS
View related parts
Ford Lower Cover, Rear
Part Number: FT4Z-17K835-FPTM
$433.90 MSRP: $680.30
You Save: $246.40 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear Lower
- Position: Rear Lower
Fits the following Ford Models:
- Edge | 2015-2018 | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Lower Cover, Front
Part Number: 6L2Z-17D957-UAPTM
$115.17 MSRP: $177.23
You Save: $62.06 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Front Lower
- Position: Front Lower
Fits the following Ford Models:
- Explorer | 2006-2010 | Eddie Bauer, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Bumper Cover, Front Upper
Part Number: FT4Z-17D957-DPTM
$331.04 MSRP: $519.03
You Save: $187.99 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Front Upper
- Position: Front Upper
Fits the following Ford Models:
- Edge | 2015-2018 | SE, SEL, Sport, Titanium | 4 Cyl 2.0 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Lower Cover, Front
Part Number: FL1Z-17D957-CA
$902.07 MSRP: $1336.40
You Save: $434.33 (33%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front Lower
- Manufacturer Note: Paint to match
- Position: Front Lower
- Replaces: FL1Z-17D957-DPTM
Fits the following Ford Models:
- Expedition | 2015-2017 | EL King Ranch, EL Limited, EL Platinum, EL XL, EL XLT, King Ranch, Limited, Platinum, XL, XLT | 6 Cyl 3.5 L GAS
View related parts
Ford Bumper Cover, Rear
Part Number: 8G1Z-17K835-CAPTM
$388.93 MSRP: $571.12
You Save: $182.19 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
Fits the following Ford Models:
- Taurus | 2008-2009 | Limited, SE, SEL | 6 Cyl 3.5 L GAS
View related parts
Ford Bumper Cover, Rear
Part Number: LJ6Z-17K835-AA
$250.43 MSRP: $367.73
You Save: $117.30 (32%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
Fits the following Ford Models:
- Escape | 2020-2022 | S, SE, SE Hybrid, SE Plug-In Hybrid, SE Sport Hybrid | 3 Cyl 1.5 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Bumper Cover, Rear
Part Number: 9S4Z-17K835-BAPTM
$208.83 MSRP: $325.28
You Save: $116.45 (36%)
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
Fits the following Ford Models:
- Focus | 2009-2011 | SE, SES | 4 Cyl 2.0 L GAS

| Page 1 of 44 |Next >

1-20 of 874 Results

Ford Bumper Parts Questions & Experts Answers

Bumper Cover, Front
2L2Z-17D957-SAPTM
Q: How to service and repair the front bumper cover on Ford Explorer?
A: Service and repair of the front bumper cover starts with disconnecting fog lamp electrical connectors when present and continuing with side lamp and front turn signal electrical connectors. The front fender inner splash shields can be accessed by removing screws and pin-type retainers followed by taking out the splash shields. You should now remove the screws located at the upper part of the bumper cover. The bottom of the front bumper cover requires rotation upward while gentle force against the top will release its four retaining tabs. The installation ends by performing the exact reverse procedure which occurred during removal.
Bumper Cover, Front
YR3Z-17D957-EA
Q: How to service the front bumper cover on Ford Mustang?
A: Start the front bumper cover service with two part pin-type retainer removal along with the removal of the radiator upper sight shield (8C288). The first step is to remove two part pin-type retainers before proceeding with the front bumper cover nuts followed by the lower bumper cover pin-type retainers. After disconnecting the two parking lamps and two headlamps, remove the mounting clips (13N129). Proceed to remove the two part pin-type retainers and the headlamps (13007) from continuation. To detach the front bumper cover (17D957) raise up the tabs at the end of the process. Installation should follow the steps in reverse order to reinstall the components.
Bumper Assembly, Rear
4L5Z-17906-DA
Q: How can you repair a damaged rear bumper cover on Ford Ranger?
A: The inspection process enables you to determine whether repairs on a damaged rear bumper cover are justified by its ability to reach an acceptable state of quality while comparing the expenses to those of a new bumper replacement. The affected bumper needs removal so technicians can cleanse the broken tab(s) by using a plastics wax and grease remover. The repair area must receive hand sanding with 80-grit paper followed by compressed air usage for debris removal. please use plastics adhesion promoter in accordance with the product label instructions. Obtain a piece of fiberglass cloth or equivalent material that will completely cover the tab's front portion and extend in a sloped 51 mm (2 in) wedge starting from the original tab position. Before adding the affected area apply the pre-prepared repair adhesive cloth patch by placing the plastic repair material patch to create the tab shape right away. A small angle sander should be used after the appropriate cure time to shape the repair tab. The sander operation must stop before the exterior surface is reached. To finish the procedure you must repair paint damage on the bumper cover while utilizing Ford-approved paint systems before reinstalling the bumper cover system.