How to Address Issues with the Automatic Transmission Shifter in a Ford Explorer?

The transmission selector lever requires servicing after positioning the gearshift lever into the NEUTRAL position. A proper back up power drain is necessary to guarantee no air bag system activation through battery cable grounding followed by one-minute wait duration followed by disconnection of all auxiliary batteries and power supplies. The first step involves removing three screws which hold the lower steering column shroud while the next step targets the release of screws securing the lower steering column opening finish panel. The upper steering column shroud must be disconnected from the steering column by removing its retaining screw before taking out the upper steering column shroud. Before you remove the gearshift lever you must install a new gearshift lever pin and then disconnect the Transmission Control Switch (TCS) electrical connector before discarding the old pin and finally taking out the gearshift lever. The TCS installation requires repeating the reverse of removal procedures before performing a TCS operational test.

How to service and repair the automatic transmission shifter on Ford Mustang?

Start the shifter automatic transmission service by first removing the shifter top control panel and disconnecting its electrical connectors. Start the process by removing the shifter bezel then take out its bulb before separating the TCS connector. Put care into lifting the handle because additional force might be needed yet excessive pulling should be avoided to stop damage to the overdrive cancel button along with its wires. Next is the responsibility to remove the screw to extract the handle. Raise and support the vehicle and disconnect the shift cable with its plastic clip for disposal. Lower the car and take out the shifter from its position. The installation requires using a fresh plastic clip followed by performing the removal steps in reverse order.

How to service and repair the automatic transmission shifter on Ford Ranger?

The service and repair of automatic transmission shifter begins with ignition switch lock cylinder removal and then proceeds to upper steering column shroud and rubber shift lever cover removal. You must disconnect the shift control selector lever harness connector then remove the gearshift lever pin which you should discard. You should now proceed to separate the gearshift lever. The installer should replace the gearshift lever pin anytime it is removed before performing a reverse installation sequence back to completion.

OEM Ford Automatic Transmission Shifter

AT Shifter

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

329 Automatic Transmission Shifters found

View related parts
Ford Shifter
Part Number: BL1Z-7210-CA
$426.99 MSRP: $627.00
You Save: $200.01 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shift Lever
Fits the following Ford Models:
- Expedition | 2011-2014 | EL King Ranch, King Ranch | 8 Cyl 5.4 L FLEX
View related parts
Ford Gear Shift Assembly, Red
Part Number: BL3Z-7210-CC
$546.98 MSRP: $810.33
You Save: $263.35 (33%)
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Shift Lever
Fits the following Ford Models:
- F-150 | 2011-2014 | FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lariat Limited, Limited, Platinum, STX, SVT Raptor, XL, XLT | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L CNG, 6 Cyl 3.7 L FLEX, 6 Cyl 3.7 L LPG, 8 Cyl 5.0 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Ford Shift Lever
Part Number: 8R3Z-7210-C
$580.39 MSRP: $859.83
You Save: $279.44 (33%)
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Automatic Transmission Shifter Cable; Shifter Assembly; Shift Control Cable
- Replaces: 7R3Z-7210-E, 7R3Z-7210-J
Fits the following Ford Models:
- Mustang | 1999-2009 | Base, Bullitt, GT, GT Bullitt, Mach 1, Shelby GT, Shelby GT500, Shelby GT500KR, SVT Cobra, SVT Cobra 10th Anniversary | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Shifter, Camel
Part Number: BL1Z-7210-BD
$426.99 MSRP: $627.00
You Save: $200.01 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shift Lever
- Manufacturer Note: Camel
Fits the following Ford Models:
- Expedition | 2012-2014 | EL XLT, XLT | 8 Cyl 5.4 L FLEX
View related parts
Ford Shifter Assembly
Part Number: BL3Z-7210-CA
$491.91 MSRP: $722.33
You Save: $230.42 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Gear Shift Assembly; Shift Lever
- Manufacturer Note: Charcoal Black
Fits the following Ford Models:
- F-150 | 2011-2014 | SVT Raptor | 8 Cyl 6.2 L GAS
View related parts
Ford Shifter Assembly
Part Number: FR3Z-7210-E
$425.74 MSRP: $625.17
You Save: $199.43 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing Assembly - Gear Shift
- Replaces: FR3Z-7210-A
Fits the following Ford Models:
- Mustang | 2024 | EcoBoost, EcoBoost Premium, GT, GT Premium | 4 Cyl 2.3 L GAS, 8 Cyl 5.0 L GAS
View related parts
Ford Shifter, Gray
Part Number: BL1Z-7210-BC
$428.24 MSRP: $628.83
You Save: $200.59 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shift Lever
Fits the following Ford Models:
- Expedition | 2012-2014 | EL Limited, Limited | 8 Cyl 5.4 L FLEX
View related parts
Ford Shift Lever
Part Number: 8R3Z-7210-D
$390.78 MSRP: $573.83
You Save: $183.05 (32%)
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Automatic Transmission Shifter Cable; Shifter Assembly; Shift Control Cable
- Replaces: 4R3Z-7213-CA, 5R3Z-7210-E, 7R3Z-7210-D, 4R3Z-7A214-A, 6R3Z-7210-F, 7R3Z-7210-H
Fits the following Ford Models:
- Mustang | 2005-2009, 1994-1998 | Base, Bullitt, GT, Shelby GT, Shelby GT500, Shelby GT500KR | 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Gear Shift Assembly, Dusk Gray
Part Number: BL3Z-7210-CB
$546.98 MSRP: $810.33
You Save: $263.35 (33%)
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Shift Lever
- Manufacturer Note: Dusk Gray
Fits the following Ford Models:
- F-150 | 2011-2014 | FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lariat Limited, Limited, Platinum, STX, SVT Raptor, XL, XLT | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L CNG, 6 Cyl 3.7 L FLEX, 6 Cyl 3.7 L LPG, 8 Cyl 5.0 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Ford Gear Shift Assembly, Black/Charcoal
Part Number: BL1Z-7210-BA
$429.48 MSRP: $630.67
You Save: $201.19 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shifter; Shift Lever
- Manufacturer Note: Charcoal Black
Fits the following Ford Models:
- Expedition | 2011-2014 | EL Limited, EL XLT, Limited, XLT | 8 Cyl 5.4 L FLEX
View related parts
Ford Shifter Assembly
Part Number: FR3Z-7210-F
$378.30 MSRP: $555.50
You Save: $177.20 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing Assembly - Gear Shift; Manual Transmission Shift Lever; Gear Shift Assembly; Shift Lever
- Replaces: FR3Z-7210-B, FR3Z-7210-C
Fits the following Ford Models:
- Mustang | 2015-2023 | Bullitt, GT, GT 50 Years Limited Edition, GT Premium, Mach 1 | 8 Cyl 5.0 L GAS
View related parts
Ford Gear Shift Assembly
Part Number: FL1Z-7210-BA
$518.13 MSRP: $760.83
You Save: $242.70 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shifter; Shift Lever
- Manufacturer Note: Ebony
Fits the following Ford Models:
- Expedition | 2015-2017 | EL King Ranch, EL Limited, EL Platinum, EL SSV, EL XL, EL XLT, King Ranch, Limited, Platinum, SSV, XL, XLT | 6 Cyl 3.5 L GAS
View related parts
Ford Shift Lever
Part Number: 5L1Z-7210-AA
$136.03 MSRP: $198.00
You Save: $61.97 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Transmission Gear Shift; Automatic Transmission Shift Lever; Gear Shift Assembly
Fits the following Ford Models:
- Expedition | 2003-2006 | Eddie Bauer, King Ranch, Limited, NBX, XLS, XLT, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Gear Shift Assembly
Part Number: JL3Z-7210-NB
$232.22 MSRP: $341.00
You Save: $108.78 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shifter; Shift Lever
- Manufacturer Note: Dark Marsala
- Replaces: JL3Z-7210-NA
Fits the following Ford Models:
- F-150 | 2018-2020 | King Ranch, Lariat, Limited, Platinum, Police Responder, Raptor, SSV, XL, XLT | 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.3 L FLEX, 6 Cyl 3.5 L GAS, 8 Cyl 5.0 L FLEX
View related parts
Ford Gear Shift Assembly
Part Number: JL3Z-7210-MB
$242.21 MSRP: $355.67
You Save: $113.46 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shifter; Shift Lever
- Manufacturer Note: Brunello With Agate Stitching
- Replaces: JL3Z-7210-MA
Fits the following Ford Models:
- F-150 | 2018-2020 | King Ranch, Lariat, Limited, Platinum, Police Responder, Raptor, SSV, XL, XLT | 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.3 L FLEX, 6 Cyl 3.5 L GAS, 8 Cyl 5.0 L FLEX
View related parts
Ford Shifter Assembly, Black
Part Number: JR3Z-7210-EB
$470.68 MSRP: $691.17
You Save: $220.49 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shift Lever; Gear Shift Assembly
- Replaces: JR3Z-7210-EA
Fits the following Ford Models:
- Mustang | 2018-2023 | EcoBoost, EcoBoost Premium, GT, GT Premium, Shelby GT500 | 4 Cyl 2.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.2 L GAS
View related parts
Ford Shift Knob
Part Number: JL3Z-7213-GA
$113.73 MSRP: $165.55
You Save: $51.82 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle Assembly; Automatic Transmission Shift Lever Knob; Automatic Transmission Selector Handle
- Manufacturer Note: Dark Ash
Fits the following Ford Models:
- F-150 | 2018-2019 | Raptor | 6 Cyl 3.5 L GAS
View related parts
Ford Gear Shift Assembly
Part Number: FL3Z-7210-EC
$227.23 MSRP: $333.67
You Save: $106.44 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shifter; Shift Lever
- Manufacturer Note: Ebony Black
- Replaces: FL3Z-7210-BA, FL3Z-7210-EB, FL3Z-7210-EA
Fits the following Ford Models:
- F-150 | 2015-2019 | Lariat, Limited, Platinum, Police Responder, Raptor, SSV, XL, XLT | 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.3 L FLEX, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 8 Cyl 5.0 L FLEX
View related parts
Ford Gear Shift Assembly
Part Number: HL3Z-7210-BB
$229.72 MSRP: $337.33
You Save: $107.61 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shifter; Shift Lever
- Manufacturer Note: Ash Stitching
- Replaces: HL3Z-7210-BA
Fits the following Ford Models:
- F-150 | 2017 | King Ranch, Lariat, Limited, Platinum, Raptor, SSV, XL, XLT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 8 Cyl 5.0 L FLEX
View related parts
Ford Gear Shift Assembly
Part Number: HL3Z-7210-NA
$232.22 MSRP: $341.00
You Save: $108.78 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shift Lever; Shifter
- Replaces: HL3Z-7210-DA, HL3Z-7210-DB
Fits the following Ford Models:
- F-150 | 2017 | King Ranch, Lariat, Limited, Platinum, Raptor, SSV, XL, XLT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 8 Cyl 5.0 L FLEX

| Page 1 of 17 |Next >

1-20 of 329 Results

Ford Automatic Transmission Shifter Parts Questions & Experts Answers

Shift Lever
5L2Z-7210-AA
Q: How to Address Issues with the Automatic Transmission Shifter in a Ford Explorer?
A: The transmission selector lever requires servicing after positioning the gearshift lever into the NEUTRAL position. A proper back up power drain is necessary to guarantee no air bag system activation through battery cable grounding followed by one-minute wait duration followed by disconnection of all auxiliary batteries and power supplies. The first step involves removing three screws which hold the lower steering column shroud while the next step targets the release of screws securing the lower steering column opening finish panel. The upper steering column shroud must be disconnected from the steering column by removing its retaining screw before taking out the upper steering column shroud. Before you remove the gearshift lever you must install a new gearshift lever pin and then disconnect the Transmission Control Switch (TCS) electrical connector before discarding the old pin and finally taking out the gearshift lever. The TCS installation requires repeating the reverse of removal procedures before performing a TCS operational test.
Shift Lever
8R3Z-7210-C
Q: How to service and repair the automatic transmission shifter on Ford Mustang?
A: Start the shifter automatic transmission service by first removing the shifter top control panel and disconnecting its electrical connectors. Start the process by removing the shifter bezel then take out its bulb before separating the TCS connector. Put care into lifting the handle because additional force might be needed yet excessive pulling should be avoided to stop damage to the overdrive cancel button along with its wires. Next is the responsibility to remove the screw to extract the handle. Raise and support the vehicle and disconnect the shift cable with its plastic clip for disposal. Lower the car and take out the shifter from its position. The installation requires using a fresh plastic clip followed by performing the removal steps in reverse order.
Shift Lever
7L5Z-7210-AA
Q: How to service and repair the automatic transmission shifter on Ford Ranger?
A: The service and repair of automatic transmission shifter begins with ignition switch lock cylinder removal and then proceeds to upper steering column shroud and rubber shift lever cover removal. You must disconnect the shift control selector lever harness connector then remove the gearshift lever pin which you should discard. You should now proceed to separate the gearshift lever. The installer should replace the gearshift lever pin anytime it is removed before performing a reverse installation sequence back to completion.